Gantner Q.bloxx A123 manuals

Q.bloxx A123

Brand: Gantner | Category: Measuring Instruments

Table of contents

1. Table Of Contents
2. Table Of Contents
3. Table Of Contents
4. Table Of Contents
5. Table Of Contents
6. Safety Information
7. Special risks
8. Disposal
9. Labels and warning information
10. Labels in this manual
11. Introduction
12. The documentation in the Q.bloxx range
13. System description
14. Operating the modules via Q.pac
15. Operating the modules without Test Controller
16. Connecting the modules
17. Hot swap (factory setting)
18. Setting the address (optional)
19. Activating the terminating resistances
20. Mounting/removing bases
21. Q.bloxx Extension Socket QES
22. Connecting the power supply
23. Fitting and removal of modules from bases
24. Connecting interfaces
25. Connecting modules to Q.pac
26. Connecting Q.gate/Q.pac via Ethernet to a PC/PLC
27. Using the RS-232 interface of Q.gate or Q.pac
28. Connecting modules directly to a PC/PLC
29. Synchronization of several systems
30. Connection of a radio receiver for time signals
31. Module flashing frequency
32. Problems during data transmission
33. The modules and their connection options
34. Q.bloxx A101: Connecting sensors and I/O
35. Current
36. Thermocouple
37. Strain-gauge quarter bridges
38. Digital input and output
39. Q.bloxx A102: Connecting sensors and I/O
43. Q.bloxx A103: Connecting sensors and I/O
45. Q.bloxx A104: Connecting sensors
47. Q.bloxx A105: Connecting sensors
48. Q.bloxx A106: Connecting sensors and I/O
49. Strain-gauge quarter bridge
50. LVDT, RVDT
52. Q.bloxx A107: Connecting sensors
55. Strain-gauge half and quarter bridges
56. Q.bloxx A108: Connecting sensors and I/O
58. Q.bloxx A109: Connecting I/O and outputs
59. Analog output, Plug 2
60. Q.bloxx A111: Connecting sensors and I/O
61. IEPE/ICP ® Sensor
62. Q.bloxx A116: Connecting sensors
63. Full and half-bridge transducers
65. Activating the shunt resistance
66. Q.bloxx A123: Connecting sensors
67. Voltage
68. Q.bloxx A124: Connecting sensors
70. Q.bloxx A127: Connecting sensors
72. Q.bloxx A128: Connecting sensors
74. Q.bloxx D101: Connecting I/O
75. Q.bloxx D104: connecting digital inputs
76. Q.bloxx D105: connecting digital outputs
77. Q.bloxx D107: Connecting digital inputs
78. Configuration
79. Installing the test.commander
80. Using test.commander
81. test.commander and the serial (service) interface
82. Creating a project for configuration
83. Configuring analog inputs
84. Carrier frequency synchronization (Q.bloxx A106)
85. Zero balancing/taring the sensor
86. Sensor scaling over several points (table)
87. Specifying digital inputs/outputs
88. Configuring analog outputs
89. Defining computations
90. Specifying the alarm monitoring
91. Q.gate and Q.pac settings
92. Host interface
93. Storage settings (only Q.pac)
94. Virtual variable
95. Online tools
96. Reading module information
97. Reading status information
98. Firmware update
99. Firmware update for modules
100. Functional Procedures
101. Bus termination on the Q.bloxx modules
102. Network topologies
103. Ethernet on the PC
104. Setting the IP address on the PC
105. Allowing access to network devices (firewall)
106. Connecting sensors with sensing leads
107. Sensor scaling
108. Scaling strain gauges
109. Current measurement with an external shunt
110. Measuring with thermocouples
111. International Sales and Service

Q.bloxx A123

Brand: Gantner | Category: Control Unit

Table of contents

1. Table Of Contents
2. Table Of Contents
3. Table Of Contents
4. Table Of Contents
5. Safety Information
6. Special risks
7. Servicing and cleaning
8. Labels and warning information
9. Labels in this manual
10. Introduction
11. The documentation in the Q.series range
12. System description
13. Operating the modules via Q.pac
14. Operating the modules without Test Controller
15. Connecting the modules
16. Using hot swap (factory setting)
17. Setting the address (optional)
18. Activating the terminating resistances
19. Mounting/removing sockets
20. Q.bloxx Extension Socket QES
21. Connecting the power supply
22. Fitting and removal of modules from sockets
23. Connecting interfaces
24. Connecting modules to Q.pac
25. Connecting Q.gate/Q.pac via Ethernet to a PC/PLC
26. Using the RS-232 interface of Q.gate or Q.pac
27. Connecting modules directly to a PC/PLC
28. Synchronization of several systems
29. Connection of a radio receiver for time signals
30. Connection of a GPS receiver
31. Activating firmware download
32. The modules and their connection options
33. Q.bloxx A101: Connecting sensors and I/O
34. Current
35. Thermocouple
36. Strain-gauge quarter bridges
37. Digital input and output
38. Q.bloxx A102: Connecting sensors and I/O
42. Q.bloxx A103: Connecting sensors and I/O
44. Q.bloxx A104: Connecting sensors
46. Q.bloxx A106: Connecting sensors and I/O
48. LVDT, RVDT
50. Q.bloxx A107: Connecting sensors
53. Strain-gauge half and quarter bridges
54. Q.bloxx A108: Connecting sensors and I/O
56. Q.bloxx A109: Connecting I/O and outputs
57. Analog output, Plug 2
58. Q.bloxx A123: Connecting sensors
59. Voltage
60. Q.bloxx A124: Connecting sensors
62. Q.bloxx A128: Connecting sensors
64. Q.bloxx D101: Connecting I/O
65. Q.bloxx D104: connecting digital inputs
66. Q.bloxx D105: connecting digital outputs
67. Configuration
68. Installing the test.commander
69. Using test.commander
70. test.commander and the serial (service) interface
71. Setting sensor parameters
72. Specifying digital inputs/outputs
73. Defining analog outputs
74. Defining computations
75. Specifying the alarm monitoring
76. Q.gate and Q.pac settings
77. Host interface
78. Logging settings (Q.pac only)
79. Virtual variable
80. Online tools, displaying measurements
81. Read module information
82. Firmware update
83. Firmware update for modules
84. Functional Procedures
85. Bus termination on the Q.bloxx modules
86. Network topologies
87. Ethernet on the PC
88. Setting the IP address on the PC
89. Allowing access to network devices (firewall)
90. Connecting sensors with sensing leads
91. Sensor scaling
92. Scaling of strain gauges
93. Current measurement with an external shunt
94. Measuring with thermocouples