143Menu Mode○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○STANDARDFor an overall bright video, there is no change(Figure on the left).For an overall dark video, the peak brightnessis reproduced even brighter (Figure on theright).MODE1, MODE2MODE3Power consumption is lowered by reducingthe brightness of an overall bight video(Figure on the left).Similar to in the STANDARD setting, an overalldark video is peak brightness is reproducedeven brighter (Figure on the right).The peak brightness in MODE2 is decreasedby a set amount with respect to that inMODE1, however it is reproduced brighterthan in MODE3.Input signal graduation is not controlled butreproduced accurately. Deterioration of thepanel due to burning is reduced since thepeak brightness of an overall dark video isnot increased.○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○12) Energy Saving SettingThis is a function that reduces power consumption and reduces deterioration of the panel by controlling the brightnessof the screen. The brightness is according to the input signal.• To make the screen bright and easy to see: Set ‘ENERGY SAVE: STANDARD’• To reduce power consumption: Set ‘ENERGY SAVE: MODE1, MODE2’• To reduce deterioration of the panel such as burning: Set ‘ENERGY SAVE: MODE 3’• To perform control according to the brightness of the room and to adjust the screen according to the surroundings:Set ‘ENERGY SAVE: AUTO’Factory setting: STANDARDDifferences in video reproduction by energy saving settings (illustration)For this kind of input signal○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○AUTO The brightness is automatically changed within the STANDARD (bright) to MODE2 (dark) range accordingto the brightness of the room.Notes• When AUTO is set, do not place objects near or let light shine directly on external sensor (see section 2.2, “ExternalDimensions” (pg. 8)).• The external sensor changes in stages; from an external light of 200 lux (rough value) to external light of 0 lux.XXXXXXXXX.(As a standard)When the white window is displayed, thepeak brightness is decreased as shownbelow.• MODE1: Decreased about 50%• MODE2: Decreased about 60%• MODE3: Decreased about 75%
