Panasonic TH-50LFC70U Operating Instructions Manual

Also see for TH-50LFC70E: Operating instructions

Contents

Panasonic TH-50LFC70U Operating Instructions Manual Manual pdf 51 page image

49ECO Mode settingsSelect “ECO Mode settings” in “Setup” menu and press button.ECO Mode settingsECO ModePower save OffOffOffDisablePC Power managementOffHDMI1 Power managementOffHDMI2 Power managementDVI-D Power managementNo signal power offCustomECO ModeCustom: The menu of power consumption reduction is individually set.On: The following xed values are set to the menu of power consumptionreduction. Individual setting is not available.Power save: On DVI-D Power management: OnHDMI1 Power management: On No signal power off: EnableHDMI2 Power management: OnPC Power management: OnUsing Remote ControlWhen is pressed, the “ECOMode” setting changes.ECO Mode OnCustom settingsThe menu of the power consumption reduction is individually set. This setting is enabled when “ECO Mode” is setto “Custom”.Power saveThis function adjusts the brightness of the backlight to reduce power consumption.Off: This function does not operate.On: Backlight brightness is reduced.Sensor: The backlight brightness is automatically adjusted according to the viewing environment.Note:When this function is set to “On” or “Sensor”, the “Backlight” setting in the Picture menu is disabled.[TH-50LFC70U, TH-65LFC70U, TH-80LFC70U, TH-50LFC70W, TH-65LFC70W and TH-80LFC70W]HDMI1 Power management, HDMI2 Power managementWhen this function is set to On, it operates under the following conditions to turn the power on or off automatically.When no pictures (sync signal) are detected for 60 or so seconds during HDMI1 or HDMI2 signal input:Power is turned off (standby); the power indicator lights up orange.When pictures (sync signal) are subsequently detected:Power is turned on; the power indicator lights up green.Note:This function is not supported by TH-50LFC70E, TH-65LFC70E and TH-80LFC70E.PC Power managementWhen this function is set to On, it operates under the following conditions to turn the power on or off automatically.When no pictures (HD/VD sync signals) are detected for 60 or so seconds during PC signal input:Power is turned off (standby); the power indicator lights up orange.When pictures (HD/VD sync signals) are subsequently detected:Power is turned on; the power indicator lights up green.Note:This function is effective when “Sync” is set to “Auto”, “Component / RGB-in select” is set to “RGB” and during normal viewing.DVI-D Power managementWhen this function is set to On, it operates under the following conditions to turn the power on or off automatically.Standard modeWhen no pictures (sync signal) are detected for 60 or so seconds during DVI signal input:Power is turned off (standby); the power indicator lights up orange.When pictures (sync signal) are subsequently detected:Power is turned on; the power indicator lights up green.Low power modeWhen +5V DC in DVI-D IN terminal or pictures (sync signal) are not detected for about 60 seconds with DVI input:Power is turned off (standby); the power indicator lights up orange.When +5V DC or pictures (sync signal) are subsequently detected:Power is turned on; the power indicator lights up green.In the Standard mode, power consumption during sleep is higher than that in the Low power mode.You can switch the Standard mode/Low power mode in “DVI Power management mode” of the Options menu. (see page 60)Notes:• This function is invalid during input from DVI-D Terminal Board (TY-FB11DD).• Depending on the type of terminal board equipped, this function may be invalid.No signal power offEquipment power supply is turned Off when there is no signal.When this is set to “Enable”, the power supply of the unit goes Off 10 minutes after the input signals stop.• For MEMORY VIEWER input, it is judged as no signal when a USB memory is not connected.