Panasonic SC-VK62D Operating Instructions Manual

Also see for SA-VK62D: Service manual

Panasonic SC-VK62D Operating Instructions Manual Manual pdf 25 page image

Other functions/Using other equipment25RQT8092ENGLISHOther functions25Muting the volumePress [MUTING].Volume is reduced to minimum.To cancelPress [MUTING] again or reduce the volume to minimum (--dB),then raise it to the required level.Muting is also canceled when you switched the unit to standby.Auto-off functionWhen disc or tape is selected as the sourceTo save power, the unit turns off if it is left unused for ten minutes.This function does not work if the source is tuner or AUX.Press [SHIFT] + [AUTO OFF].“AUTO OFF” is shown on the main unit’s display.The setting is maintained even if the unit is turned off.If you select tuner or AUX as the source, “AUTO OFF” goes out. Itcomes on again when you select disc or tape.To cancelPress [SHIFT]+[AUTO OFF] again.Dimming the displayPress [SHIFT] + [DIMMER].To return to the original brightness, press [SHIFT]+[DIMMER] again.Changing the main unit’s displayPress [DISP MODE] to select the desired display mode.Every time you press the button:Peak holdNormal(off)ReflectionUsing other equipmentUsing headphones1 Reduce the volume and connect the headphones (notincluded).Headphone plug type: 3.5 mm stereo2 Adjust headphone volume with [VOLUME DOWN, UP]on the main unit.NoteAvoid listening for prolonged periods of time to prevent hearingdamage.Operating a televisionPoint the remote control at the television for the following operations.Turning the television on/offPress [SHIFT] + [TVfffff].Switching the television’s video input modePress [SHIFT] + [TV/AV].Changing channelsPress [SHIFT] + [TV CH44444] or [SHIFT] + [TV CH33333].Adjusting the volumePress [SHIFT] + [TV VOL+] or [SHIFT] + [–TV VOL].NoteSome models cannot be operated by this remote control.Changing the main unit and remote control modeThe remote control and main unit are factory-set to “REMOTE 1”mode.If your remote control affects other equipment during operation, youcan switch to operate in “REMOTE 2” mode.To switch to “REMOTE 2” mode11111 While pressing and holding [AUX] on the main unitPress and hold [2] until “REMOTE 2” appears on themain unit display.22222 Press and hold [ENTER] and [2] for at least 2seconds.The main unit and remote control are now set to operate in“REMOTE 2” mode.To return to “REMOTE 1” modeDo steps 1 and 2 above but use [1] instead of [2] for both steps.(“REMOTE 1” appears on the main unit during step 1.)The remote control cannot work with the main unit if theirmodes are different.“REMOTE 1” or “REMOTE 2” appears on the main unit display whenyou operate the remote control.If “REMOTE 1” appears (The main unit is in “REMOTE 1” mode.)Press and hold [ENTER] and [1] on the remote control for at least2 seconds.If “REMOTE 2” appears (The main unit is in “REMOTE 2” mode.)Press and hold [ENTER] and [2] on the remote control for at least2 seconds.NoteYou can still operate a television using the remote control (A seeabove) even after switching the mode.Using an external unitYou can connect an analog player with a built-in phono equalizer.(L)(R)Back ofthe mainunitAnalog player(not included)R L1 Press [TUNER/AUX] (main unit: [AUX]) to select“AUX”.The unit comes on.2 For listening : Proceed to step 3.For recording : Press [[ REC] on the main unit(recording starts).Press [L] (main unit: [L, STOP]) tostop recording.3 Start playback from external source.• For details, refer to the instruction manual of the units which are tobe connected.• When units other than those described above are to beconnected, please consult your audio dealer.Using other equipment