Panasonic DIGA DMR-BW750 Operating Instructions Manual

Contents

96RQT9428These settings are used when you will connect this unit to anetwork.The connection to the Internet may take time or the internetmay not be connected depending on the connection environment. Itis recommended that you use a broadband connection.■ Testing the connectionAlways test the connection when a LAN cable is connected or whennew “IP Address/DNS Settings” have been made.1 Press [FUNCTION MENU].2 Press [e, r] to select “Others” and press [OK].3 Press [e, r] to select “Setup” and press [OK].4 Press [e, r] to select “Network Settings” andpress [OK].5 Press [e, r] to select “IP Address/DNSSettings” and press [OK].6 Press [e, r] to select “Connection Test” andpress [OK].RETURNOKIP Address / DNS SettingsConnection TestOnOnOnOnOnOnIP Address Auto-assignmentIP AddressSubnet MaskGateway AddressDNS-IP Auto-assignmentPrimary DNSSecondary DNSConnection Speed Auto-configureConnection Speed SettingMAC Address: 00-0b-97-e6-7a-ae“Testing”: The test is in progress.“OK”: The connection is completed.“Failed”: Please check the connection and settings.Notey Perform the “Connection Test” also when any change was made tothe “IP Address / DNS Settings”.y If the connection test fails, it may be necessary to set the MACaddress of this unit at the router side. The MAC address can bedisplayed by selecting “Network Settings” and “IP Address / DNSSettings” in steps 1-5 (➡ above).■ Setting the IP addressIn most cases, default settings can normally be used withoutmaking any changes.Set the IP address only when the router has no DHCP serverfunctions or when the router’s DHCP server function is disabled.After performing steps 1–5 (➡ above)6 Press [e, r] to select “IP Address Auto-assignment” and press [w, q] to select “Off”.7 Press [e, r] to select “IP Address”, “SubnetMask” or “Gateway Address” and press [OK].8 Enter numbers with the numbered buttons andpress [OK].y After checking the specifi cations for your broadband router,enter each number.If the number is unknown, then check the number of otherdevices such as personal computers connected via a LANcable. Assign a different number from those of other devices for“IP Address” and the same number for others.y If a wrong number is entered, then press [DEL].192 . . .1IP AddressPlease input IP Address and press “OK”.The IP address will be cleared by pressing“OK” when there is no number input.0 - Number99 Press [w, q] to select “Yes” and press [OK].Notey The numeric input range is between 0 and 255.■ Setting the DNS-IPIn most cases, default settings can normally be used withoutmaking any changes.When setting an assigned DNS server from your internet serviceprovider, perform the following settings.After performing steps 1–5 (➡ left)6 Press [e, r] to select “DNS-IP Auto-assignment” and press [w, q] to select “Off”.7 Press [e, r] to select “Primary DNS” or“Secondary DNS” and press [OK].8 Enter numbers with the numbered buttons andpress [OK].y Follow the instructions given by your internet service providerand enter the numbers. If the number is unknown, then checkthe number of other devices such as personal computersconnected via a LAN cable and assign the same number.y If a wrong number is entered, then press [DEL].9 Press [w, q] to select “Yes” and press [OK].Notey The numeric input range is between 0 and 255.■ Setting the connection speedWhen the connection test results in “Failed” after the IP and DNS-IPaddresses are assigned, perform the following settings.After performing steps 1–5 (➡ left)6 Press [e, r] to select “Connection Speed Auto-confi gure” and press [w, q] to select “Off”.7 Press [e, r] to select “Connection SpeedSetting” and press [w, q] to select a connectionspeed.y Select a connection speed in accordance with the environmentof the network connected.y When the settings are changed, the network connection maybe disabled depending on the device.Network Settings