Honeywell LYNX Touch Series Installation And Setup Manual

Also see for LYNX Touch Series: User guide Guide Installation and setup guide Programming guide Quick installation guide

Contents

Honeywell LYNX Touch Series Installation And Setup Manual Manual pdf 9 page image

LYNX Touch Installation and Setup Guide- 9 -AC Power and Backup BatteryThe system is powered by a 9 Volt DC, 2.7 Amp Plug-in Power Supply, 300-04705 or 300-04065 (300-04063in Canada). Refer to the wiring table below for wire gauge and length. In the event of an AC power loss, thesystem is supported by a long life backup battery that is supervised for connection and for low voltageconditions. If the battery is missing, or a low battery condition is detected, a “low battery” message isdisplayed and a report is sent to the central station. In addition, the system will beep once every 45 secondsto audibly indicate a low battery condition (press any key to stop the beeping).Use only the provided 300-04705 or 300-04065 (300-04063 Canada) Power Supply. Wiring to the PowerSupply must not exceed 300 feet using 16-gauge wire.Do not plug the power supply into the AC outlet until after all wiring connections have been made. Ensure thecover is snapped closed prior to applying AC powerThe LYNX Touch is equipped with an integral, replaceable, rechargeable battery pack rated at 7.2Vdc.Select the appropriate battery pack, based on the installation’s requirement, and install the battery pack.5000-100-093-V0ORRETAINERSCREWRETAINERSCREWRemove battery retainer.Insert battery pack into back case.Route cable through channel (cutout) on left side ofcompartment.Install battery retainer.Secure battery retainer with the provided screw.Secure battery wiring in the wire routing clips (3).Connect the battery connector to the receptacle on the PCboard.After the wiring connection has been made, snap the frontand the back case closed.Plug the power supply into a 24-hour, 110VAC unswitchedoutlet. Upon powerup, the system will display "Please WaitChecking System Integrity".When battery replacement is required, unplug thetransformer from the wall outlet, and open the control panelcover.Remove the screw that secures the battery retainer.Remove the battery retainer and disconnect the batterypack connector from the receptacle on the PC Board.Remove the battery pack from the back case.Install a replacement battery pack (P/N 300-03864-1/LYNXRCHKIT-SC or P/N 300-03866/LYNXCHKIT-SHA)into the back case.Route cable through channel (cutout) on left side ofcompartment.Install the battery retainer.Secure battery retainer with the provided screw.Secure battery wiring in the wire routing clips (3).Connect the battery connector to the receptacle on the PCboard.After the wiring connection has been made, snap the frontand the back case closed.Plug the power supply into a 24-hour, 110VAC unswitchedoutlet. Upon powerup, the system will display "Please WaitChecking System Integrity".Battery SelectionThe LYNX Touch is equipped with an integral, replaceable, rechargeablebattery pack rated at 7.2Vdc. Select the appropriate battery pack,based on the installation's requirement, and install the battery pack.Battery Part Number Battery StandbyTime Low Battery Notification300-03866/LYNXRCHKIT-SHA300-03864-1/LYNXRCHKIT-SC 4-hours (minimum) Approximately 1-hour before battery depletionm f r24-hours (mini um) At least 1-hour be ore batte y depletionInstalling the Rechargeable Backup BatteryReplacing the Rechargeable Backup Battery1.2.3.4.5.6.7.8.9.1.2.3.4.5.6.7.8.9.10.11.BATTERYCABLECHANNELBATTERYWIRE ROUTINGCLIPS (3)Ensure the control panel assembly is snapped closedprior to applying AC power. Rechargeable batteries maytake up to 48-hours to fully charge. The "Low Battery"message should clear within four hours or by entering anOFF sequence.BATTERY PACK(P/N 300-03866/LYNXRCHKIT-SHA)BATTERY PACK(P/N 300-03864-1/LYNXRCHKIT-SC)WWW.DIYALARMFORUM.COM