Menu
GE C70 Instruction Manual
Also see for C70: Communications manualCommunications guideInstruction manualInstruction manualInstruction manual
                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                    | |
Contents
| 
GE Multilin C70 Capacitor Bank Protection and Control System 2-12 PRODUCT DESCRIPTION 2.1 INTRODUCTION22 PRODUCT DESCRIPTION 2.1INTRODUCTION 2.1.1 OVERVIEWThe C70 Capacitor Bank Protection and Control System is a UR-series microprocessor-based relay for protection and con-trol of small, medium, and large three-phase capacitor banks. The relay can be ordered with up to three CT/VT modules,allowing for flexible application to variety of bank configurations.The key protection functions are designed to cover grounded and ungrounded, single and parallel banks. Sensitive protec-tion functions support compensation for both external (system) unbalance and inherent unbalance of the capacitor bankitself. Both voltage and current-based balance protection functions are available. Algorithms are developed to automaticallyselect compensation settings after repairs or other alternations of the bank.The relay supports variety of bank configurations through flexible configurations of its AC inputs, installed voltage and cur-rent transformers, and resulting protection techniques.The relay incorporates an automatic voltage regulator (AVR) responding to either voltage, reactive power, or power factor.A separate timer function initiates controls on a pre-defined time/date basis. These on-off type controls are meant to auto-matically close or open the associated breaker. A supervisory function is provided to program the local/remote, auto/man-ual functionality, temporary inhibit closing after tripping, and other auxiliary functions such as operation counters.A capacitor control element provides remote/local and auto/manual control regulation, trip/close interlocking, and seal-in. Auser-programmable time delay inhibits closing until after the bank discharges itself to a safe level.The relay can also equipped with a serial 64/128 kbps direct input/output module for fast and reliable peer-to-peer commu-nication with other UR-series IEDs.The C70 metering functions include true RMS and phasors for currents and voltages, current and voltage harmonics andTHD, symmetrical components, frequency, power, power factor.Diagnostic features include an event recorder capable of storing 1024 time-tagged events, oscillography capable of storingup to 64 records with programmable trigger, content and sampling rate, and data logger acquisition of up to 16 channels,with programmable content and sampling rate. The internal clock used for time-tagging can be synchronized with an IRIG-B signal, using the Simple Network Time Protocol (SNTP) over the Ethernet port, or using the Precision Time Protocol(PTP). This precise time stamping allows the sequence of events to be determined throughout the system. Events can alsobe programmed (via FlexLogic™) to trigger oscillography data capture which may be set to record the measured parame-ters before and after the event for viewing on a personal computer. These tools significantly reduce troubleshooting timeand simplify report generation in the event of a system fault.Several options are available for communication. A faceplate RS232 port can be used to connect to a computer for the pro-gramming of settings and the monitoring of actual values. The RS232 port has a fixed baud rate of 19.2 kbps. The rearRS485 port allows independent access by operating and engineering staff. It can be connected to system computers withbaud rates up to 115.2 kbps. All serial ports use the Modbus RTU protocol. The IEC 60870-5-103 protocol is supported onthe RS485 interface. IEC 60870-5-103, DNP, and Modbus cannot be enabled simultaneously on this interface. Also onlyone of the DNP, IEC 60870-5-103, and IEC 60870-5-104 protocols can be enabled at any time on the relay. When the IEC60870-5-103 protocol is chosen, the RS485 port has a fixed even parity and the baud rate can be either 9.6 kbps or 19.2kbps. The 100Base-FX or 100Base-T Ethernet interface provides fast, reliable communications in noisy environments. TheEthernet port supports IEC 61850, Modbus/TCP, and TFTP protocols, PTP (according to IEEE Std. 1588-2008 or IEC61588), and allows access to the relay via any standard web browser (C70 web pages). The IEC 60870-5-104 protocol issupported on the Ethernet port. The Ethernet port also supports the Parallel Redundancy Protocol (PRP) of IEC 62439-3(clause 4, 2012) when purchased as an option.Settings and actual values can be accessed from the front panel or EnerVista software.The C70 IEDs use flash memory technology which allows field upgrading as new features are added. The following singleline diagram illustrates the relay functionality using ANSI (American National Standards Institute) device numbers. |
Related manuals for GE C70
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved