OneStart

GDC SX-3000 Installation Manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Page 38 preview
Page 39 preview
Page 40 preview
Page 41 preview
Page 42 preview
Page 43 preview
Page 44 preview
Page 45 preview
Page 46 preview
Page 47 preview
Page 48 preview
Page 49 preview
Page 50 preview
Page 51 preview
Page 52 preview
Page 53 preview
Page 54 preview
Page 55 preview
Page 56 preview
Page 57 preview
Page 58 preview
Page 59 preview
Page 60 preview
Page 61 preview
Page 62 preview
Page 63 preview
Page 64 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. Table Of Contents
  4. INTRODUCTION
  5. Equipment List
  6. INSTALLING SX-3000 INTO THE PROJECTOR
  7. Remove existing interface board/placeholders from projector
  8. Christie Projector Placement
  9. Inserting SX-3000 into the projector
  10. INSTALLING PSD-3000-P PORTABLE STORAGE DEVICE
  11. Front Panel
  12. Installing the Bracket on a Barco S2K projector
  13. Installing the Bracket on a NEC S2K projector
  14. Installing the Bracket on a Barco B or C Series projector
  15. Installing the Bracket on a NEC 2K or 4K projector
  16. Installing the Bracket on a Christie CP2220 or CP2230 projector
  17. eSATA Connection to the SX-3000
  18. Procedure to Install the HDDs
  19. PSD-3000-P Indicator
  20. Warning Buzzer
  21. OPERATION OF PSD-3000-P
  22. Hard Disk Information
  23. Increase Rebuild Speed
  24. IMB Network Setup
  25. Projector Connection
  26. Barco Series 2 Projector Setup
  27. Barco Touch Panel Setup
  28. NEC Series 2 Projector
  29. Christie Series 2 Projector
  30. D settings for Series 2 projectors
  31. IMB 3D macro settings changes
  32. Time Zone Setup
  33. Content Ingest Management Setup
  34. Content ingest from FTP
  35. Audio Setup
  36. Digital-to-Analog Converters
  37. AUTOMATION SETUP
  38. Adding event labels and actions
  39. Automation Scheduling
  40. Automation setup for server GPIO
  41. Automation setup for eCNA devices
  42. Automation setup for JNIOR devices
  43. Automation setup for Christie ACT devices
  44. Automation setup for Dolby devices
  45. Automation setup for USL DAX devices
  46. Automation setup for USL JSD devices
  47. SETUP
  48. AES Audio and GPIO Pinout
/ 64
Related manuals for GDC PSD-3000-P
GDC AIB-3000 User Manual first page preview
GDC AIB-3000 User Manual
This manual is suitable for:
PSD-3000-PSX-3000