Canon Super G3 Fax Board-AF1 Service Manual

Canon Super G3 Fax Board-AF1 Service Manual Manual pdf 70 page image

Chapter 66-26.2 Service Error Code6.2.1 Service Error Code 0025-3174T-6-2No. T/R Description##100 [T] at time of transmission, the procedural signal has been transmitted more than specified.##101 [T/R] the modem speed does not match that of the other party.##102 [T] at time of transmission, fall-back cannot be used.##103 [R] at time of reception, EOL cannot be detected for 5 sec (15 sec if CBT).##104 [T] at time of transmission, RTN or PIN is received.##106 [R] at time of reception, the procedural signal is received for 6 sec while in wait for the signal.##107 [R] at time of reception, the transmitting party cannot use fall-back.##109 [T] at time of transmission, a signal other than DIS, DTC, FTT, CFR, or CRP is received, and the procedural signal has been sent more thanspecified.##111 [T/R] memory error has occurred.##114 [R] at time of reception, RTN is transmitted.##200 [R] at time of reception, no image carrier is detected for 5 sec.##201 [T/R] DCN is received outside the normal parity procedure.##204 [T] DTC without transmission data is received.##220 [T/R] system error (main program out of control) has occurred.##223 [T/R] while a communication is under way, the line is cut.##224 [T/R] in G3 communication, an error has occurred in the procedural signal.##226 [T/R] the stack printer has fallen outside the RAM area.##229 [R] the recording unit has remained locked for 1 min.##232 [T] encoding error has occurred.##237 [R] decoding error has occurred.##238 [R] the print control unit is out of order.##261 [T/R] system error has occurred.##280 [T] at time of transmission, the procedural signal has been transmitted more than specified.##281 [T] at time of transmission, the procedural signal has been transmitted more than specified.##282 [T] at time of transmission, the procedural signal has been transmitted more than specified.##283 [T] at time of transmission, the procedural signal has been transmitted more than specified.##284 [T] at time of transmission, DCN is received after transmission of TCF.##285 [T] at time of transmission, DCN is received after transmission of EOP.##286 [T] at time of transmission, DCN is received after transmission of EOM.##287 [T] at time of transmission DCN is received after transmission of MPS.##288 [T] after transmission of EOP, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.##289 [T] after transmission of EOM, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.##290 [T] after transmission of MPS, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.##670 [T] at time of V.8 late start, the V.8 ability of DIS front the receiving party is expected to be detected, and the CI signal is expected to betransmitted in response; however, the procedure fails to advance, and the line is released because of T1 time-out.##671 [R] at time of V.8 arrival, procedure fails to move to phase 2 after detection of CM signal from caller, causing T1 time-out and releasing line.##672 [T] at time of V.34 transmission, a shift in procedure from phase 2 to phase 3 and thereafter stops, causing the machine to release the line andsuffer T1 timeout.##673 [R] at time of V.34 reception, a shift in procedure from phase 2 to phase 3 and thereafter stops, causing the machine to release the line and sufferT1 timeout.##674 [T] at time of V.34 transmission, a shift in procedure from phase 3 and phase 4 to the control channel and thereafter stops, causing the machineto release the line and suffer T1 timeout.##675 [R] at time of V.34 reception, a shift in procedure from phase 3 and phase 4 to the control channel and thereafter stops, causing the machine torelease the line and suffer T1 timeout.##750 [T] at time of ECM transmission, no meaningful signal is received after transmission of PPS-NULL, causing the procedural signal to betransmitted more than specified.##752 [T] at time of ECM transmission, DCN is received after transmission of PPS-NULL.##753 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-NULL, or T5 time-out (60 sec) has occurred.##754 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-NULL.##755 [T] at time of ECM transmission, no meaningful signal is received after transmission of PPS-MPS, causing the procedural signal to be transmittedmore than specified.##757 [T] at time of ECM transmission, DCN is received after retransmission of PPS-MPS.##758 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-MPS, or T5 time-out(60 sec) has occurred.##759 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-MPS.##760 [T] at time of ECM transmission, no meaningful signal is received after transmission of PPS-EOM, causing the procedural signal to betransmitted more than specified.