Canon Super G3 Fax Board-AF1 Service Manual

Canon Super G3 Fax Board-AF1 Service Manual Manual pdf 71 page image

Chapter 66-3##762 [T] at time of ECM transmission, DCN is received after transmission of PPS-EOM.##763 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-MPS, or T5 time-out(60 sec) has occurred.##764 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-EOM.##765 [T] at time of ECM transmission, no meaningful signal is received after transmission of PPS-EOP, causing the procedural signal to be transmittedmore than specified.##767 [T] at time of ECM transmission, DCN is received after transmission of PPS-EOP.##768 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-EOP, or T5 time-out(60 sec) has occurred.##769 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-EOP.##770 [T] at time of ECM transmission, no meaningful signal is received after transmission of EOR-NULL, causing the procedural signal to betransmitted more than specified.##772 [T] at time of ECM transmission, DCN is received after transmission of EOR-NULL.##773 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of EOR-NULL, or T5 time-out (60 sec) has occurred.##774 [T] at time of ECM transmission, ERR is received after transmission of EOR-NULL.##775 [T] at time of ECM transmission, no meaningful signal is received after transmission of EOR-MPS, causing the procedural signal to betransmitted more than specified.##777 [T] at time of ECM transmission, DCN is received after transmission of EOR-MPS.##778 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission EOR-MPS, or T5 time-out(60 sec) has occurred.##779 [T] at time of ECM transmission, ERR is received after transmission of EOR-MPS.##780 [T] at time of ECM transmission, no meaningful signal is received after transmission of EOR-EOM, causing the procedural signal to betransmitted more than specified.##782 [T] at time of ECM transmission, DCN is received after transmission of EOR-EOM.##783 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of EOR-EOM, or T5 time-out (60 sec) has occurred.##784 [T] at time of ECM transmission, ERR is received after transmission of EOR-EOM.##785 [T] at time of ECM transmission, no meaningful signal is received after transmission of EOR-EOP, causing the procedural signal to betransmitted more than specified.##787 [T] at time of ECM transmission, DCN is received after transmission of EOR-EOP.##788 [T] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of EOR-EOP, or T5 time-out(60 sec) has occurred.##789 [T] at time of ECM transmission, ERR is received after transmission of EOR-EOP.##790 [R] at time of ECM reception, ERR is transmitted after transmission of EOR-Q.##791 [T/R] while ECM mode procedure is under way, a signal other than a meaningful signal is received.##792 [R] at time of ECM reception, PPS-NULL cannot be detected over partial page processing.##793 [R] at time of ECM reception, no effective frame is received while high-speed signal reception is under way, thus causing time-out.##794 [T] at time of ECM reception, PPR with all 0s is received.##795 [T/R] a fault has occurred in code processing for communication.##796 [T/R] a fault has occurred in decoding processing after reception of ECMNo. T/R Description

/ 74

Related manuals for Canon Super G3 Fax Board-AF1