Cal Amp VIPER SC+ 140-5098-304 manuals

VIPER SC+ 140-5098-304

Brand: Cal Amp | Category: Network Router

Table of contents

1. important notice
2. Table Of Contents
3. Table Of Contents
4. Table Of Contents
5. Table Of Contents
6. Table Of Contents
7. General Description
8. Physical Description
9. Front Panel
10. ethernet lan port
11. power connector
12. Part Numbers and Availability
13. Fan Kits and Cables
14. Components
15. Two- and Three-Piece Kit Additional Items
16. Network Architecture
17. Point-to-Point Network
18. Report by Exception Configuration
19. IP Forwarding Modes
20. Router Mode
21. Viper Router Generator (VRG) Program
22. Understanding RF Path Requirements
23. Site Selection and Site Survey
24. Antenna Overview
25. Good Design Practices
26. Selecting Antenna and Feedline
27. Feedline
28. Terrain and Signal Strength
29. Install the Antenna
30. Connect the Viper SC+ to Programming PC
31. Introduction to the Viper SC+ Web Interface
32. Initial Configuration Using the Setup Wizard
33. Setup Wizard Step 1: Station Name and Mode Settings
34. Setup Wizard Step 2: Network IP Settings
35. Setup Wizard Step 3: Radio Setup
36. Setup Wizard Step 4: Encryption
37. Viper SC+ Web Interface
38. Home
39. RF Status
40. Basic Settings
41. Radio Settings
42. CWID
43. RF Tests
44. RF Network Settings
45. RF Bandwidth Management
46. additional settings
47. Neighbor Table
48. neighbor discovery
49. Global Settings
50. VLAN
51. vlan configuration
52. vlan membership
53. QoS Statistics
54. LAN Settings
55. DHCP
56. SNTP
57. time zone
58. Broadcast Multicast
60. Ethernet (PHY)
61. Routing Table
62. Serial
64. Advanced
65. Security
66. AES Encryption
67. RADIUS
68. client configuration
69. service control
70. status and statistics
71. Diagnostics
72. Remote Statistics
73. SNMP
74. Online Diagnostics
75. Radio Log
76. Device Maintenance
77. factory settings
78. Package Control
79. general settings
80. Network Optimization
81. Use Data Retries
82. Using CalAmp-Provided and Cloned Viper Configurations
83. Cloning a Viper
84. Upgrading Firmware
85. Upgrade the Radio Firmware
86. APPENDIX A – Abbreviations and Definitions
87. APPENDIX B – Viper SC+™ Specifications
88. Viper SC+™ Overall Dimensions and Mounting Hole Locations
89. APPENDIX C – Viper SC+™ Regulatory Certifications
90. DECLARATION OF CONFORMITY FOR MODELS # 140-5018-60x, 140-5048-40x, and 140-5048-60x
91. EU and EFTA Member States' Acceptable Frequency Table
92. APPENDIX D – UL Installation Instructions
93. APPENDIX E – Viper SC+™ Site Installation and Setup General Guidelines
94. Viper Configuration (Radio and Controller Board for Base Station)
95. APPENDIX F – Viper SC+™ Power-Save Mode
96. Power Save Mode FAQs
97. APPENDIX G – NAT Overview
98. NAT on Viper
99. RF Interface Private
100. User NAT Entries
101. NAT Port Forwarding
102. APPENDIX H – MIB File Overview
103. APPENDIX I – VLAN Introduction
104. VLAN Untagging
105. Tagged Mode
106. VLAN Member Table
107. Bridge Mode (VLAN Disabled)
108. Bridge Mode (VLAN Enabled)
109. APPENDIX J – Viper PLC Setup
110. Polling Remote PLCs Non sequentially
111. Closing Old TCP Connection
112. Avoid Unnecessary Traffic Over The Air Network
113. PLC Ladder Logic On Restart Opens All Connections At Once Instead Of Sequentially
114. Allen-Bradley Micrologix 1100 or 1400 (may also apply to SLC 5)
115. More about Message Reply Timeout
116. PLC Reopens TCP/IP Connection With the Same Source Port
117. Allen-Bradley ControlLogix and CompactLogics PLC for Viper System
118. Overriding the Default Inactivity Timeout —Not Recommended Unless Required
119. Summary On TCP Connection Timeout (Inactivity Setting)
120. When Communication Is Between ControlLogix or CompactLogix And Other –Logix Series PLCs
122. Summary of Connected or Unconnected Operation
123. APPENDIX K – Service And Support And Warranty Statement
124. Warranty Statement