Electrolux 40" manuals
40"
Table of contents
- SAFE SERVICING PRACTICES
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- QUICK REFERENCE SHEET
- MAXIMUM ALLOWABLE SURFACE TEMPERATURES
- SECTIONA - 30" ELECTRIC FREESTANDING INSTALLATION INSTRUCTIONS
- Serial plate information
- Grounding instructions
- Leveling the range
- Drill pilot holes and fasten bracket
- SECTION A - 40" ELECTRIC FREESTANDING INSTALLATION INSTRUCTIONS
- Important notes to the installer
- For models with self-clean feature
- Three conductor wire connection to range
- Direct electrical connection to the circuit
- Junction box location
- Preparation
- When all hookups are complete
- SECTION B - ACCESSORIES
- Troubleshooting
- Element does not cycle
- Both elements do not heat
- Top element electronic control system
- How it operates
- F6 code:
- Blank display
- How to program the ES 100
- To broil
- Calibration
- normally, the broil element heats but the bake element does not heat
- Sample schematic for ES 100 control system
- The ES 200 electronic oven control system
- To change the oven temperature after baking has started
- To set the controls for a self-clean cycle
- Broil
- F9 code:
- Lock motor runs continuously
- The ES 300 electronic oven control system
- To change the minute timer while it is in use
- To program oven for a delayed start time and to shut-off automatically
- Time bake
- the broil element does not heat
- Oven door locks when the oven is programmed for clean but the oven does not heat
- The ES 400 electronic oven control system
- To cancel the minute timer before the set time has run out
- Preheat
- Convection bake
- When the self-clean cycle is completed
- Convection roast
- Broil element does not heat
- The ES 450 Electronic Oven Control System
- Minute timer
- immediately and to shut off automatically
- To program the oven for a delayed start time and to shutoff automatically
- To adjust the oven temperature lower
- Convection element does not operate
- The PRC Glass touch electronic oven control models
- Electronic Oven Control
- Timer reminder
- Bake
- Timed bake
- Delayed timed bake
- To set the controls for the self-cleaning cycle to start immediately and shut off automatically
- To start the delayed self-clean cycle
- Adjusting oven temperature
- Capacitance touch glass
- Oven door does not lock when the oven is programmed for clean
- Sample schematic for PRC Glass touch control system
- If the element does not cycle off
- Top trim on backguard area
- Removing the oven light or fluorescent switch
- Removing electronic oven control
- Removing the large element safety thermostat
- Removing indicator lights
- Removing the end caps
- Terminal block
- Removing the main top (smooth top models)
- Removing the burner pan (coil models)
- Removing the oven door
- Removing the inner door heat shield
- Inside the oven
- Removing the oven vent (coil top models and bottom part of the vent system on smooth top models)
- Removing the oven light socket
- Removing the drawer glide
- Removing side rail on from the drawer
- Removing the warmer drawer diode
- Removing the top of the warmer drawer cavity
- Removing the leveling leg and roller assembly
- Removing small panel
- Removing the lock motor assembly
- Removing the door switch
- SECTION E - 40" DISASSEMBLY AND REPLACEMENT OF PARTS
- Removing the thermostat and top element knobs
- Removing the control panel
- Removing rear hinge
- Removing the front oven trim
- Removing the large oven door outer panel
- Removing the wool shield
- Removing the seal between the inner glass and the inner door liner in the large oven door
- Removing large oven bake element
- Removing the large oven vent
- Removing the small oven broil element
- Bodyside
- Removing the side heat shield
- Removing the large door righthand hinge roller bracket
40"
Table of contents