Menu
Valley VRI-iS Installation Manual
                                                                                                      | |
Contents
| 
47Field Install and Wiring DiagramsVRI-iS Slip Ring Field Install pn 9312418#1 BLACK#2 BLACK#3 BLACKBLK,RED,GRNYEL,ORG,BROREDBLACKWHITETO FIRSTVALVETERMINAL BLOCKDETAILFROMRESOLVERWHITE/ORANGEWHITE/BROWNWHITE/BLACKWHITE/REDWHT/BLKWHT/ORGWHT/REDSCALE:SOFTWARE: AUTOCADSHEET:REF:DATE:RTHIRD ANGLETOLERANCE UNLESS OTHERWISE SPECIFIED:DRAWN DESIGN AUTHORIZE28800 Ida Street Valley, Nebraska 68064-0358PART NO.:PART NAME:DIMENSIONS IN BRACKETS [XX,X] ARE MILLIMETERSDESCRIPTIONECN DATEECN NO.REV.LINEAR DIMENSIONS:ANGULAR DIMENSIONS:DRILLED HOLES:OTHER HOLES:9312418VRI-iS SLIP RING WIRING FIELD INSTALLMAMJWB TAT XX-XX-XX 1.000 1 OF 1INSUL-8 COLLECTOR RING AEROMOTIVE COLLECTOR RING5/16 NUTS & BOLTSREMOVE KNOCK-OUT INBOTTOM OF COLLECTORRING HOUSINGLEAVE EXISTING LOCKNUT ONTOP OF RING STACK. USE #8NUT & WASHER SUPPLIED WITHCOLLECTOR RING TO ATTACHMOUNT BRACKETS ON TOP OFLOCKNUTS.SEE SLIP RING DETAILSEE TERMINALBLOCK DETAIL9312412-MOUNTING BRACKET (3 REQ'D)*SEE DETAIL A*IMPORTANT: POWER AND CONTROL WIRINGMUST CLEAR SENSOR BRACKET.IF NECESSARY, USE A LARGEWIRE TIE TO BUNDLE WIRESAWAY FROM BRACKET.LONG SENSOR BRACKETWIRE TIE HOLDER (2 REQ'D)#4 X 5/8 40UNC 2A SCREW (2 REQ'D)#4 HEX NUT W/LOCKWASHER (2 REQ'D)4 POSITION TERM. BLOCK#10 x 3/4 R.H. SCREW PLT (3 REQ'D)#10 LOCK WASHER PLT (3 REQ'D)#10 HEX NUT PLT (6 REQ'D)(TYP. FOR ALL STANDOFF BRACKETS)COLLECTOR RINGSEE SLIP RING DETAIL SEE TERMINAL BLOCK DETAIL9361174-MOUNTING BRACKET (3 REQ'D)*SEE DETAIL B*IMPORTANT: POWER AND CONTROL WIRINGMUST CLEAR SENSOR BRACKET.IF NECESSARY, USE A LARGEWIRE TIE TO BUNDLE WIRESAWAY FROM BRACKET.SHORT SENSOR BRACKETWIRE TIE HOLDER (2 REQ'D)#4 X 5/8 40UNC 2A SCREW (2 REQ'D)#4 HEX NUT W/LOCKWASHER (2 REQ'D)4 POSITION TERM. BLOCK#10 x 3/4 R.H. SCREW PLT (3 REQ'D)#10 LOCK WASHER PLT (3 REQ'D)#10 HEX NUT PLT (6 REQ'D)(TYP. FOR ALL STANDOFF BRACKETS)COLLECTOR RINGNOTE: INSTALL SENSOR BRACKET TO THE EXISTING 5/16"BOLT OPPOSITE TO THE 1/2" NPT PIPE PLUG TOGAIN MAXIMUM CLEARANCE FOR THE SENSOR ARM.1/2" NPT STRAIN RELIEFEXISTING 5/16 BOLT & HARDWARE5/16-18 UNC-2B HEX NUT PLTREMOVE ANY (3) OF THE (4)EXISTING #8 HARDWARE TOINSTALL STANDOFF BRACKETS.1/4 FLAT WASHER WIDE PLT(TYP. FOR ALL STANDOFF BRACKETS)IMPORTANT: THE LOCATION OF THESEWASHERS IS CRITICAL!!A 31789 05-07-18 NO CHANGES TO DWG. BOM CHANGE ONLY. SV/TATWIRE NUTNOTE:CLIP/TRIM DRAIN WIRE IN COLLECTORRING COMING UP FROM PANEL. CONNECTDRAIN WIRE FROM FIRST VALVE TOGROUND IN COLLECTOR RING.NOTE:CONNECT DRAIN WIRE TOGROUND IN PANELTURN CLOCKWISETO MAX. VOLTAGETO FIRSTVALVETO TERM.BLOCKTO TERM.BLOCKTO TERM.BLOCK1/2" NPT GALVANIZED NIPPLE1/2 ROMAX NUT (2 REQ'D).50 STRAIN RELIEF1/2 HUB CORD CONNECTORTO FIRST VALVERUNNING LIGHT CABLE1/2 T-UNILET CONDUIT ASSEMBLYOPTIONAL INSTALLATION DETAILOPTIONAL HARDWARE USED WHEN INSTALLING WITH RUN LIGHT* SEE OPTIONALINSTALLATION DETAIL *COLLECTOR RINGEXISTINGWIRES1/2" NPT STRAIN RELIEFTO FIRSTVALVE* SEE OPTIONALINSTALLATION DETAIL *DETAIL BDETAIL ALOCATE I.D. HOLE TOWARDSBOTTOM OF COLLECTOR RINGUSE ONLY ON AEROMOTIVECOLLECTOR RING(NO I.D. HOLE)USE ONLY ON INSUL-8COLLECTOR RINGPANEL DETAILSLIP RINGDETAIL±.06 [1.5]± 1°+.010 [.25]/-.002 [.05]±.010 [.25] |
Related manuals for Valley VRI-iS
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved