Sharp SPC1100 Instructions & Warranty

Also see for SPC1100: Instructions & warranty User manual

Atomic QA Wall ClockInstructions & WarrantyThank you for your purchase of this quality clock. The utmost care has gone into the design and manufacture of yourclock. Please read these instructions and store them in a safe place for future reference.The receiver unit has a clear, easy-to-read display that shows indoor temperature, outdoor temperature and 12hour weather forecast. The remote sensor transmits the outdoor temperature. To receive the outdoor temperature,place the sensor anywhere within 100 feet ; the 433.92MHz technology means no wire installation is required.The Atomic Clock will always be accurate to within one second as it receives daily WWVB updates. Daylight SavingTime also automatically updates so there is no need to re-set the clock manually!The clock has a built in receiver that automatically synchronizes itself with the WWVB radio signal broadcast by theUS Governmentís National Institute of Standards & Technology (NIST) in Fort Collins, Colorado.IMPORTANT: If the Atomic Clock does not receive the WWVB signal immediately, wait overnight and it will beset in the morning.FEATURES:Atomic QA Clock1The WWVB radiosignal daily broadcast ensures that the atomic clock will always display the most accurate date and time.. QA Clock:2. LCD WEATHER FORECAST DISPLAY3. BATTERY COMPARTMENT AND DOOR:- Before inserting the battery, select the Time Zone andand stop at zero position (12:00), and then the minute and hour hands will start running andThen, the clock begins to receive the Atomic time signal automatically and it will take 3 - 10receive the signal, the hands will find their correct time and work normally.1. The unit will automatically search for the time signal at 2:16am, 4:16am, 2:16pm, 4:16pm.2. Closed area such as airport, basement, tower block or factory is not recommended.3. While the atomic signal is flashing, the control panel is inactive.- Displays indoor/outdoor temperature and 12 hour weather forecast;- Use 2 x AA size batteriesNOTE:RECWWVBM.SETChannelResetC / FRECWWVBM.SET1 2 4 5 63 7 9 10 11 12 13 148- In normal mode, press the button to switch the between channel 1, 2 and 3 to receive the 433.92MHz signal;press and hold the button for 3 seconds to pair with the outdoor remote sensor.In case of malfunction, press RESET button to reset all values to default values.- In normal mode, press and hold the M.SET button, second hand will stop and enter into manual setting. Keeppressing the M.Set button, the minute hand will run quickly. Release the button to exit the manual setting andthe clock will start running within a few seconds.- In normal mode, press and hold the REC button, the hands will stop running and enter into Force Receivingmode. It will start receiving the Atomic time signal within 10 minutes. Once received the signal successfully,the clock hands will found the correct time and run normally. Otherwise, it will return to the time before ForceReceiving. If the Atomic signal is not received wait over night and it will be set in the morning.- Before insert the battery, select the DST mode. The clock has programmed to automatically switch when thedaylight saving time is in effect.- Before insert the battery, select the correct time zone. The default time zone is P (Pacific Time). If your locationis not in the Pacific, slide the time zone switch to M (Mountain Time) / C (Central Time) / E (Eastern Time) zone.- Function same as No. 9- Function same as No. 8- Use 1 x AA size battery5. Channel BUTTON:6. Reset BUTTON:7. WALL MOUNT8. M. SET (Manual Set) BUTTON:9. REC (Force Receiving) BUTTON:10. DST ON/OFF SWITCH:11. TIME ZONE SWITCH:12. REC BUTTON:13. M. SET BUTTON:14. BATTERY COMPARTMENT AND DOOR:NOTE:LCD WEATHER FORECAST DISPLAY1.The accuracy of a general pressure-based weather forecast is about 70% - 75%.2.The weather forecast is meant for next 12 hours. It my not necessarily reflect the current situation.3.The “Sunny“ icon, when applied to nighttime, implies clear weather.4. BUTTON:- In normal mode, press the butt n to switch temperature unit °C/°F.°C/°FSunny, Sunny Intervals, Cloudy, Rain, Rain + Thunder, SnowDST mode (Daylight Savings Time) . Once battery is inserted, thesecond hand will runstop at zero position.minutes. If successfullySunnySunny IntervalsCloudyRainRain + ThunderSnow

/ 2

Related manuals for Sharp SPC1100