Sealey LED013 Instruction Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructionsand properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONALREQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THEPURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONALINJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY1.1. GENERAL Ensure the lamp is fully charged before initial use. DO NOT turn the lamp on when it is being charged. DO NOT shine directly into your, other person’s oranimal’s eyes. DO NOT allow children to use the lamp. DO NOT handle or move the lamp whilst it is beingcharged. DO NOT use the lamp if you suspect that the battery orthe lamp casing is damaged. DO NOT leave battery in a discharged state, rechargebattery immediately. Before storage, fully recharge thebattery, subsequently recharge the battery at least onceevery six months of non-use.1.2. ELECTRICAL SAFETY FOR USE OF CHARGER.USE ONLY THE SUPPLIED CHARGER PLUG FORCONNECTING TORCH TO THE POWER SUPPLY. WARNING! It is the user’s responsibility to read,understand and comply with the following electricalinstructions:You must ensure the risk of electric shock is minimisedby the installation of appropriate safety devices.An RCCB (Residual Current Circuit Breaker) should beincorporated in the main distribution board. We alsorecommend that an RCD (Residual Current Device) isused with all electrical products, particularly portableequipment which is plugged into an electrical supply notprotected by an RCCB.You must also read and understand the following instructionsconcerning electrical safety.1.2.1. The Electricity At Work Act 1989requires all portable electrical appliances, if used onbusiness premises, to be tested by a qualified electrician,using a Portable Appliance Tester (PAT), at least once ayear.1.2.2. The Health & Safety at Work Act 1974 makes ownersof electrical appliances responsible for the safe conditionof the appliance and the safety of the appliance operator.If in any doubt about electrical safety, contact aqualified electrician.1.2.3. You must ensure that you: Inspect the charger plug, cable and connector for wearand damage to ensure items are safe before connectingto the mains power supply.If worn or damaged DO NOT use. Important: Check that the voltage marked on the chargerplug is the same as the power supply to be used. Uncoil the cable between charger and the lamp. DO NOT pull the charger plug from the mains socket bythe lead. WARNING! DO NOT use any other type of chargerwith this product, other than the supplied mains orcar charger. Failure to observe this warning couldresult in injury and or fire and will invalidate thewarranty. DO NOT try to take the charger plug apart. DO NOT use the charger plug to charge or power anyother electrical item. DO NOT get the charger wet, or use in wet, dampconditions (for indoor use only).1.3 Battery Safety WARNING! To reduce the risk of burns or fire: DO NOT Attempt to open, disassemble, modify orservice the battery pack. DO NOT Crush, puncture, short external contacts ordispose of in fire or water. DO NOT Expose to temperatures above 60°C (140°). Replace only with the battery pack designated for thisproduct. Recycle or dispose of used battery as stipulated by localregulation. If the electrolyte in the cells gets on your skin, thoroughlywash with soap and water. If it gets in your eyes, rinsethoroughly with cool water and seek immediate medicalattention.INSTRUCTION MANUAL FOR:CORDLESS 36LED RECHARGEABLEINSPECTION LAMPMODEL No's. LED013Original Language Version LED013 Issue: 3 - 22/12/11Robust inspection lamp with lightweight Lithium-ion batterysuitable for the professional user. Incorporates 36 super brightLED's ideal for use in engine bays and under-body inspection.For hands-free applications features both, fold-away 360° swivelhanging hook and an integral magnet.Battery: ............................................................. 7.4V / 1Ah Li-ionCharging Time: .....................................................................4hrsOperating Time: ....................................................................5hrsOperating Temp: ...................................................... -5°C ~ 45°CStorage Temp: ....................................................... -20°C ~ 40°C2. INTRODUCTION / SPECIFICATION3. CHARGING IMPORTANT WARRANTY INFORMATION:The battery fitted to this lamp is considered to be aconsumable item and its ability to accept charge willreduce over time. We will warranty it against mechanicaland electrical defect for a period of one year - this doesnot cover fair wear and tear. If the battery is not properlycharged before first use, or regularly conditioned, itscapacity will diminish. Under these circumstances we willnot replace the battery even if it is less than one year old.3.1 Connect the charger into the charge socket on thelamp. Plug into power supply and turn on, the redcharge LEDs on the lamp (Fig.1) will light to showcharging has commenced.3.2 When the battery has fully charged (approx 4hrs) thered LEDs will go out and green LED's will comeon. Disconnect from mains supply.3.3 During usage, when the battery is low the redcharging LED's will start to flash. When this happensswitch off the lamp and re-charge.Note: The Lithium battery does not suffer from memoryeffect and once fully charged may be stored for up tosix months without another charge.

/ 2

Related manuals for Sealey LED013