Sealey LED0121R Instructions Manual

INSTRUCTIONS FORCOB LED INTERCHANGEABLE INSPECTIONLAMP & TORCH RECHARGEABLEMODEL NO: LED0121RThank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY1.1. ELECTRICAL SAFETY FOR USE OF CHARGER. WARNING! DO NOT use any other type of charger with this product, other than the supplied mains or car charger. Failure to observethis warning could result in injury and or fire and will invalidate the warranty. WARNING! It is the user’s responsibility to read, understand and comply with the following electrical instructions:You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices.An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD(Residual Current Device) is used with all electrical products, particularly portable equipment which is plugged into an electricalsupply not protected by an RCCB.9 You must also read and understand the following instructions concerning electrical safety.The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualifiedelectrician, using a Portable Appliance Tester (PAT), at least once a year.The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance andthe safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.9 You must ensure that you Inspect the charger plug, cable and connector for wear and damage to ensure items are safe beforeconnecting to the mains power supply. If worn or damaged DO NOT use.9 Check that the voltage marked on the charger plug is the same as the torch.9 Uncoil the cable between charger and the lamp.9 Inspect the cable and connector for wear and damage to ensure items are safe before connecting to the power supply. If worn ordamaged DO NOT use.9 Ensure the torch is fully charged before initial use.8 DO NOT charge in damp conditions.8 DO NOT turn the torch on when it is being charged.8 DO NOT shine directly into your, another person’s or an animal’s eyes.8 DO NOT allow children to use the torch.8 DO NOT handle or move the torch whilst it is being charged.8 DO NOT use the torch if you suspect that the battery or the torch casing is damaged.8 DO NOT leave battery in a discharged state, recharge battery immediately. Before storage, fully recharge the battery, subsequentlyrecharge the battery at least once every six months of non-use.8 DO NOT attempt to open, disassemble, modify or service the battery.8 DO NOT crush, puncture, short external contacts or dispose of in fire or water.9 Replace only with the battery designated for this product.9 Recycle or dispose of used battery as stipulated by local regulation.9 If the electrolyte in the cells gets on your skin, thoroughly wash with soap and water. If it gets in your eyes, rinse thoroughly with coolwater and seek immediate medical attention.IMPORTANT WARRANTY INFORMATIONThe battery fitted to this lamp is considered to be a consumable item and its ability to accept a charge will reduce over time.We will provide warranty against mechanical and electrical defect for a period of one year - this does not cover fair wear and tear.If the battery is not properly charged before first use, or regularly conditioned, its capacity will diminish.Under these circumstances we will not replace the battery regardless of whether the battery is less than one year old.2. INTRODUCTIONInnovative two in one interchangeable worklight with quick release function. Includes 250 lumen torch with sliding focus, and a slimline 350lumen COB inspection lamp with 180° tilt function and an additional LED directional torch. Features a power indicator on the switch and amagnet on the base for hands free operation. Supplied in a presentation box. Features a lithium battery and is supplied with a high quality USBcharging cable and mains charger. Can be used with attachment LED0121F (Flexible inspection lamp).Refer toinstructionsLED0121R | Issue 2 22/08/17Original Language Version© Jack Sealey Limited

/ 3

Related manuals for Sealey LED0121R