Panasonic TX-43FX550B Operating Instructions Manual

Panasonic TX-43FX550B Operating Instructions Manual Manual pdf 7 page image

English - 6 -Ultra HD (UHD)TV supports Ultra HD (Ultra High Definition - alsoknown as 4K) which provides resolution of 3840 x2160 (4K:2K). It equals 4 times the resolution of FullHD TV by doubling the pixel count of the Full HD TVboth horizontally and vertically. Ultra HD contents aresupported from HDMI, USB inputs and over DVB-T2and DVB-S2 broadcasts.High Dynamic Range (HDR) / Hybrid Log-Gamma(HLG)Using this feature the TV can reproduce greaterdynamic range of luminosity by capturing and thencombining several different exposures. HDR/HLGpromises better picture quality thanks to brighter, morerealistic highlights, more realistic colour and otherimprovements. It delivers the look that filmmakersintended to achieve, showing the hidden areas ofdark shadows and sunlight with full clarity, colour anddetail. HDR/HLG contents are supported via nativeand market applications, HDMI, USB inputs and overDVB-S broadcasts. Set the related HDMI sourceinput as Enhanced from the Sources option in theSettings>System menu in order to watch HDR/HLGcontent, if the HDR/HLG content is received throughan HDMI input. The source device should also be atleast HDMI 2.0a compatible in this case.Accessories Included• Remote Control• Batteries: 2 x AA• Instruction Book• Detachable stand• Stand mounting screws (M4 x 12)Standby NotificationsIf the TV does not receive any input signal (e.g. froman aerial or HDMI source) for 3 minutes, it will gointo standby. When you next switch-on, the followingmessage will be displayed: “TV switched to stand-bymode automatically because there was no signalfor a long time.”The Auto TV OFF option(in the Settings>System>More menu) could have been set to a value between1 and 8 hours by default. If this setting is not set as Offand the TV has been left on and not been operatedduring the set time, it will switch into standby modeafter the set time has expired. When you next switch-onthe TV, the following message will be displayed. “TVswitched to stand-by mode automatically becauseno operation was made for a long time.” Before theTV switches into standby mode a dialogue window willbe displayed. If you do not press any button the TVwill switch into the standby mode after a waiting periodof about 5 minutes. You can highlight Yes and pressOK to switch the TV into standby mode immediately.If you highlight No and press OK, the TV will remainon. You can also choose to cancel the Auto TV OFFfunction from this dialogue. Highlight Disable andpress OK, the TV will remain on and the function willbe cancelled. You can enable this function again bychanging the setting of the Auto TV OFF option fromthe Settings>System>More menu.TV Control & OperationP+V+ V-P-The joystick allows you to control the Volume /Programme / Source and Standby-On functions ofthe TV.Note: The position of the joystick may differ depending onthe model.To change volume: Increase the volume by pushingthe joystick right. Decrease the volume by pushingthe joystick left.To change channel: Scroll through the storedchannels by pushing the joystick up or down.To change source: Press the centre of the joystickin, the sources list will appear on the screen. Scrollthrough the available sources by pushing the joystickup or down.To turn the TV off: Press the centre of the joystick inand hold it down for a few seconds, the TV will turninto standby mode.To turn on the TV: Press the centre of the joystick in,the TV will turn on.Note: Main menu OSD cannot be displayed via joystick.Operation with the Remote ControlPress the Home button on your remote control todisplay main menu. Use the directional buttons andOK button to navigate and set. Press Return/Backor Home button to quit a menu screen.Input SelectionOnce you have connected external systems to yourTV, you can switch to different input sources. Press theSource button on your remote control consecutivelyto select the different sources.Changing Channels and VolumeYou can change the channel and adjust the volumeby using the Programme +/- and Volume +/- buttonson the remote.