Panasonic TX-43FX550B Operating Instructions Manual

Panasonic TX-43FX550B Operating Instructions Manual Manual pdf 16 page image

English - 15 -satellite search is performed some settings should bemade. Antenna Type menu will be displayed first. Youcan select Antenna Type as Direct, Single SatelliteCable or DiSEqC switch by using Left or Rightbuttons. After selecting your antenna type press OK tosee the options to proceed. Continue, Transponderlist and Configure LNB options will be available. Youcan change the transponder and LNB settings usingthe related menu options.• Direct: If you have a single receiver and a directsatellite dish, select this antenna type. Press OK tocontinue. Select an available satellite on the nextscreen and press OK to scan for services.• Single Satellite Cable: If you have multiplereceivers and a single satellite cable system, selectthis antenna type. Press OK to continue. Configuresettings by following instructions on the next screen.Press OK to scan for services.• DiSEqC switch: If you have multiple satellite dishesand a DiSEqC switch, select this antenna type. Thenset the DiSEqC version and press OK to continue.You can set up to four satellites (if available) forversion v1.0 and sixteen satellites for version v1.1on the next screen. Press OK button to scan the firstsatellite in the list.Analogue: If Analogue broadcast search option isturned on, the TV will search for analogue broadcastsafter other initial settings are completed.After the initial settings are completed TV will startto search for available broadcasts of the selectedbroadcast types.While the search continues current scan results willbe displayed at the bottom of the screen. After all theavailable stations are stored, Channels menu will bedisplayed. You can edit the channel list according toyour preferences using the Edit tab options or pressthe Home button to quit and watch TV.While the search continues a message may appear,asking whether you want to sort channels accordingto the LCN(*). Select Yes and press OK to confirm.(*) LCN is the Logical Channel Number system that organizesavailable broadcasts in accordance with a recognizablechannel number sequence (if available).Note: Do not turn off the TV while initializing first timeinstallation. Note that, some options may not be availabledepending on the country selection.Media Playback via USB InputYou can connect 2.5” and 3.5” inch (HDD with external powersupply) external hard disk drives or USB memory stick to yourTV by using the USB inputs of the TV.IMPORTANT! Back up the files on your storage devicesbefore connecting them to the TV. Manufacturer willnot be responsible for any file damage or data loss.Certain types of USB devices (e.g. MP3 Players)or USB hard disk drives/memory sticks may not becompatible with this TV. The TV supports FAT32 andNTFS disk formatting.Wait a little while before each plugging and unpluggingas the player may still be reading files. Failure to doso may cause physical damage to the USB playerand the USB device itself. Do not pull out your drivewhile playing a file.You can use USB hubs with your TV’s USB inputs.External power supplied USB hubs are recommendedin such a case.It is recommended to use the TV’s USB input(s)directly, if you are going to connect a USB hard disk.Note: When viewing image files the Media Browser menucan only display 1000 image files stored on the connectedUSB device.Media BrowserYou can play back music and movie files and displayphoto files stored on a USB storage device byconnecting it to your TV. Connect a USB storage deviceto one of the USB inputs located on the side of the TV.After connecting a USB storage device to your TVMedia Browser menu will be displayed on the screen.You can access the content of the connected USBdevice any time later from the Sources menu. Selectthe related USB input option from this menu and pressOK. Then select the file of your choice and press OKto display or play it back.You can set your Media Browser preferences by usingthe Settings menu. Settings menu can be accessedvia the information bar which is displayed on thebottom of the screen when pressed the Info buttonwhile playing back a video file or displaying a picturefile. Press the Info button, highlight the gear wheelsymbol positioned on the right side of the informationbar and press OK. Picture Settings, Sound Settings,Media Browser Settings and Options menus will beavailable. The contents of these menus may changeaccording to the type of the currently open media file.Only Sound Settings menu will be available whileplaying back audio files.Loop/Shuffle Mode OperationStart playback and activateAll files in the list will becontinuously played inoriginal orderStart playback and activateThe same file will beplayed continuously(repeat)Start playback and activateAll files in the list will beplayed once in randomorderStart playback and activate ,All files in the list will becontinuously played inthe same random orderTo use the functions on the information bar highlight thesymbol of the function and press OK. To change the