Chapter 9 Network Connection — Network settings- 176 -Connecting to the wireless access point ([INFRA(SELECT)]/[INFRA(MANUAL)])This is the setting to connect the unit to a wireless access point.When connecting by searching the wireless access point (SSID)1 Select the [NETWORK] menu → [DEVICE SEL] → [WLAN].2 Select the [NETWORK] menu → [WLAN PROPERTY] → [TYPE] → [INFRA(SELECT)].3 Select the [NETWORK] menu → [WLAN IPv4 SETTING] → [DHCP] → [CLIENT].When the wireless access point DHCP function is not to be used, select [OFF].4 Select the [NETWORK] menu → [WLAN PROPERTY] and [WLAN IPv4 SETTING] and set each item as required.≥ For the setting items, refer to “Setting items for [WLAN PROPERTY] and [WLAN IPv4 SETTING] when set to either [INFRA(SELECT)] or[INFRA(MANUAL)]” (l 176).5 Select the SSID of the searched wireless access point.Setting is completed when the [ENCRYPT KEY] (encryption key, password) is not set.6 If the [ENCRYPT KEY] is set, enter the password, and select [Enter].7 Close the menu or return to the level of the [NETWORK] menu.8 Check the network connection.Once connected, is displayed on the screen of the unit.When entering the wireless access point (SSID) manually1 Select the [NETWORK] menu → [DEVICE SEL] → [WLAN].2 Select the [NETWORK] menu → [WLAN PROPERTY] → [TYPE] → [INFRA(MANUAL)].3 Select the [NETWORK] menu → [WLAN PROPERTY] and [WLAN IPv4 SETTING] and set each item as required.≥ For the setting items, refer to “Setting items for [WLAN PROPERTY] and [WLAN IPv4 SETTING] when set to either [INFRA(SELECT)] or[INFRA(MANUAL)]” (l 176).4 In [NETWORK] menu → [WLAN PROPERTY] and [WLAN IPv4 SETTING] → [SSID], enter the SSID of the wireless access pointbeing connected to.Setting is completed when the [ENCRYPT KEY] (encryption key, password) is not set.5 If the [ENCRYPT KEY] is set, enter the password, and select [Enter].6 Close the menu or return to the level of the [NETWORK] menu.7 Check the network connection.Once connected, is displayed on the screen of the unit.∫ Setting items for [WLAN PROPERTY] and [WLAN IPv4 SETTING] when set to either [INFRA(SELECT)] or [INFRA(MANUAL)]@ NOTE0 Depending on your environment, the communication speed may become slower or the wireless access point may not be available for use.0 The startup time after turning on the power may be longer due to starting of the network.0 When changing the settings of [DEVICE SEL], the changes will not be reflected until the unit is restarted. Also, the setting screen termination may takesome time due to the restart of the network service after the setting is changed.0 ENCRYPTION in WEP is not supported.0 Some items cannot be set depending on the settings such as [DHCP].[WLAN PROPERTY] [ENCRYPTION] [WPA-TKIP], [WPA-AES], [WPA2-TKIP], [WPA2-AES], [NONE](Factory setting: [WPA2-AES])[ENCRYPT KEY] WPA/WPA2 encryption key(Factory setting: [01234567890123456789abcdef])[WLAN IPv4 SETTING] [DHCP] Setting the DHCP function≥ [OFF]: Does not use DHCP.≥ [CLIENT]: Automatically acquired with the DHCP.(Factory setting: [OFF])[IP ADDRESS] IP address of the unit(Factory setting: [192.168.0.1])[SUBNET MASK] Subnet mask(Factory setting: [255.255.255.0])[DEFAULT GATEWAY] Default gateway(Factory setting: [192.168.0.254])[PRIMARY DNS] Primary DNS server setting(Factory setting: [0.0.0.0])[SECONDARY DNS] Secondary DNS server setting(Factory setting: [0.0.0.0])
