Canon iR2030 Series Service Manual

Also see for iR2018 Series: Service manual Brochure & specs Brochure & specs Easy operation guide Portable manual

Contents

Canon iR2030 Series Service Manual Manual pdf 259 page image

Chapter 1414-11##0286 [Tx] at time of transmission, DCN is received after transmission of EOM.##0287 [Tx] at time of transmission DCN is received after transmission of MPS.##0288 [Tx] after transmission of EOP, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.##0289 [Tx] after transmission of EOM, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.##0290 [Tx] after transmission of MPS, a signal other than PIN, PIP, MCF, RTP, or RTN has been received.##0670 [Tx] at time of V.8 late start, the V.8 ability of DIS front the receiving party is expected to be detected, and the CI signal is expectedto be transmitted in response; however, the procedure fails to advance, and the line is released because of T1 time-out.##0671 [Rx] at time of V.8 arrival, procedure fails to move to phase 2 after detection of CM signal from caller, causing T1 time-out andreleasing line##0672 [Tx] at time of V.34 transmission, a shift in procedure from phase 2 to phase 3 and thereafter stops, causing the machine to releasethe line and suffer T1 timeout.##0673 [Rx] at time of V.34 reception, a shift in procedure from phase 2 to phase 3 and thereafter stops, causing the machine to release theline and suffer T1 timeout.##0674 [Tx] at time of V.34 transmission, a shift in procedure from phase 3 and phase 4 to the control channel and thereafter stops, causingthe machine to release the line and suffer T1 timeout.##0675 [Rx] at time of V.34 reception, a shift in procedure from phase 3 and phase 4 to the control channel and thereafter stops, causing themachine to release the line and suffer T1 timeout.##0750 [Tx] at time of ECM transmission, no meaningful signal is received after transmission of PPS-NULL, causing the procedural signalto be transmitted more than specified.##0752 [Tx] at time of ECM transmission, DCN is received after transmission of PPS-NULL.##0753 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-NULL,or T5 time-out (60 sec) has occurred.##0754 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-NULL.##0755 [Tx] at time of ECM transmission, no meaningful signal is received after transmission of PPS-MPS, causing the procedural signal tobe transmitted more than specified.##0757 [Tx] at time of ECM transmission, DCN is received after retransmission of PPS-MPS.##0758 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-MPS, orT5 time-out (60 sec) has occurred.##0759 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-MPS.##0760 [Tx] at time of ECM transmission, no meaningful signal is received after transmission of PPS-EOM, causing the procedural signal tobe transmitted more than specified.##0762 [Tx] at time of ECM transmission, DCN is received after transmission of PPS-EOM.##0763 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-MPS, orT5 time-out (60 sec) has occurred.##0764 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-EOM.##0765 [Tx] at time of ECM transmission, no meaningful signal is received after transmission of PPS-EOP, causing the procedural signal tobe transmitted more than specified.##0767 [Tx] at time of ECM transmission, DCN is received after transmission of PPS-EOP.##0768 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-EOP, orT5 time-out (60 sec) has occurred.##0769 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of PPS-EOP.##0770 [Tx] at time of ECM transmission, no meaningful signal is received after transmission of EOR-NULL, causing the procedural signalto be transmitted more than specified.##0772 [Tx] at time of ECM transmission, DCN is received after transmission of EOR-NULL.##0773 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of EOR-NULL,or T5 time-out (60 sec) has occurred.##0774 [Tx] at time of ECM transmission, ERR is received after transmission of EOR-NULL.##0775 [Tx] at time of ECM transmission, no meaningful signal is received after transmission of EOR-MPS, causing the procedural signal tobe transmitted more than specified.##0777 [Tx] at time of ECM transmission, DCN is received after transmission of EOR-MPS.##0778 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission EOR-MPS, orT5 time-out (60 sec) has occurred.##0779 [Tx] at time of ECM transmission, ERR is received after transmission of EOR-MPS.##0780 [Tx] at time of ECM transmission, no meaningful signal is received after transmission of EOR-EOM, causing the procedural signalto be transmitted more than specified.##0782 [Tx] at time of ECM transmission, DCN is received after transmission of EOR-EOM.##0783 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of EOR-EOM,or T5 time-out (60 sec) has occurred.##0784 [Tx] at time of ECM transmission, ERR is received after transmission of EOR-EOM.##0785 [Tx] at time of ECM transmission, no meaningful signal is received after transmission of EOR-EOP, causing the procedural signal tobe transmitted more than specified.##0787 [Tx] at time of ECM transmission, DCN is received after transmission of EOR-EOP.##0788 [Tx] at time of ECM transmission, the procedural signal has been transmitted more than specified after transmission of EOR-EOP, orT5 time-out (60 sec) has occurred.##0789 [Tx] at time of ECM transmission, ERR is received after transmission of EOR-EOP.##0790 [Rx] at time of ECM reception, ERR is transmitted after transmission of EOR-Q.##0791 [Tx/Rx] while ECM mode procedure is under way, a signal other than a meaningful signal is received.##0792 [Rx] at time of ECM reception, PPS-NULL cannot be detected over partial page processing.##0793 [Rx] at time of ECM reception, no effective frame is received while high-speed signal reception is under way, thus causing time-out.##0794 [Tx] at time of ECM reception, PPR with all 0s is received.##0795 [Tx/Rx] a fault has occurred in code processing for communication.No. Tx/Rx Description