OneStart

Menu

ADT ADT-UDACT Product Information

Also see for ADT-UDACT: Manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Page 38 preview
Page 39 preview
Page 40 preview
Page 41 preview
Page 42 preview
Page 43 preview
Page 44 preview
Page 45 preview
Page 46 preview
Page 47 preview
Page 48 preview
Page 49 preview
Page 50 preview
Page 51 preview
Page 52 preview
Page 53 preview
Page 54 preview
Page 55 preview
Page 56 preview
Page 57 preview
Page 58 preview
Page 59 preview
Page 60 preview
Page 61 preview
Page 62 preview
Page 63 preview
Page 64 preview
Page 65 preview
Page 66 preview
Page 67 preview
Page 68 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. NFPA Standards, NFPA 72 National Fire Alarm Code
  4. Product Description
  5. Figure 1-1: ADT-UDACT Assembly
  6. Controls and Indicators
  7. Circuits
  8. Specifications
  9. Modes and Special Functions
  10. Clear Function
  11. Installation and Wiring
  12. Figure 2-2: Relay Driver Connections
  13. Figure 2-3: Monitoring for ADT-UDACT Trouble
  14. Figure 2-4: Typical Wiring Diagram for UL Power-limited Requirements
  15. Programming Instructions
  16. Switch Functions
  17. Table 3-1: Start and End Monitoring Addresses
  18. Table 3-2: Event Codes, Primary Number
  19. Table 3-3: Event Codes, Primary Number
  20. Table 3-4: Ademco Contact ID, Primary Number
  21. Table 3-5: Event Codes, Secondary Number
  22. Table 3-6: Event Codes, Secondary Number
  23. Table 3-7: Ademco Contact ID, Secondary Number
  24. Operating Instructions
  25. Displays
  26. Figure 4-1: ADT-UDACT Phone Connectors and LEDs
  27. Key Report Descriptions
  28. Disabling of Zones or Points
  29. Zone or Point Supervisory
  30. Figure 4-2: Handset/Speaker Connection
  31. Reporting Formats
  32. Table 5-2: Letter Code Definitions
  33. Table 5-3: Ademco Contact ID Reporting Structure
  34. Compatible Receivers
  35. Programming Reference Sheets
  36. Appendix B: Point Assignments (Unimode 300*/400)
  37. Appendix C: Point Assignments (ADT-MNNA)
  38. Appendix D: Unimode 2020/1010
  39. Figure D-3: EIA-485 Connection to Panel Mounted ADT-UDACT
  40. Figure D-4: EIA-485 Connection to Remote ADT-UDACT
  41. Appendix E: Unimode 300/400
  42. Figure E-3: Unimode 400 External ADT-UDACT Mounting in ADT-ABS8RF
  43. Appendix F: ADT-MNNA
  44. Appendix G: Annunciators
ADT ADT-UDACT Product Information Manual pdf 40 page image
Document 50934 Rev B 5/15/00 PN 50934:B40The reporting structure for the Ademco Contact ID format is as follows:SSSS 18 QXYZ GG CCCwhereSSSS = Four digit Subscriber ID (addresses 17 - 20 and43 - 46)18 = Identifies transmission as Contact ID to thereceiver at the Central StationQ = Event Qualifier1 = New Event2 = New RestoreXYZ = Event code (shown in Tables 3-4 and 3-7)GG = Group number or Loop numberCCC = Device or Zone numberFor general reports (alarm, trouble and supervisory), the GG and CCC fieldsare transmitted as 00 and 000 unless changes to addresses 64-65 and 66-68are made.64 - 65 = Loop number (GG), (factory default is 00)66 - 68 = Device/Zone number (CCC) for General Alarm,Fault or Supervisory messages (factory default is 000).A typical printout of alarm and trouble reports in the Ademco Contact IDReporting Structure follows:Time Date SSSS QXYZ GG CCCC411:28 03/25 11 7777 E110 00 C000 - general alarm11:28 03/25 11 7777 E111 00 C046 - alarm SD4611:28 03/25 11 7777 E300 00 C000 - general trouble11:28 03/25 11 7777 E380 00 C046 - trouble SD4611:28 03/25 11 7777 R110 00 C000 - general alarm restore11:28 03/25 11 7777 R111 00 C046 - alarm SD46 restore11:28 03/25 11 7777 R300 00 C000 - general trbl restore11:28 03/25 11 7777 R380 00 C046 - trouble SD46 restoreTable 5-3: Ademco Contact ID Reporting StructureNotes:1) In the sample report, SD46 refers to smoke detector at address 46 oron zone 46.2) 18, which is used in the reporting structure to identify the transmissionas Contact ID, is not printed out in the alarm and trouble report.3) Q, which is the Event Qualifier for the reporting structure, is printed outin the report as an E for New Event or R for New Restore.4) CCCC, the first C is not transmitted by the ADT-UDACT but is printedby the Central Station Receiver printer output.Rcvr/Line ID
/ 68
This manual is suitable for:
ADT-UDACT
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved