OneStart

Menu

ADT ADT-UDACT Product Information

Also see for ADT-UDACT: Manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Page 38 preview
Page 39 preview
Page 40 preview
Page 41 preview
Page 42 preview
Page 43 preview
Page 44 preview
Page 45 preview
Page 46 preview
Page 47 preview
Page 48 preview
Page 49 preview
Page 50 preview
Page 51 preview
Page 52 preview
Page 53 preview
Page 54 preview
Page 55 preview
Page 56 preview
Page 57 preview
Page 58 preview
Page 59 preview
Page 60 preview
Page 61 preview
Page 62 preview
Page 63 preview
Page 64 preview
Page 65 preview
Page 66 preview
Page 67 preview
Page 68 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. NFPA Standards, NFPA 72 National Fire Alarm Code
  4. Product Description
  5. Figure 1-1: ADT-UDACT Assembly
  6. Controls and Indicators
  7. Circuits
  8. Specifications
  9. Modes and Special Functions
  10. Clear Function
  11. Installation and Wiring
  12. Figure 2-2: Relay Driver Connections
  13. Figure 2-3: Monitoring for ADT-UDACT Trouble
  14. Figure 2-4: Typical Wiring Diagram for UL Power-limited Requirements
  15. Programming Instructions
  16. Switch Functions
  17. Table 3-1: Start and End Monitoring Addresses
  18. Table 3-2: Event Codes, Primary Number
  19. Table 3-3: Event Codes, Primary Number
  20. Table 3-4: Ademco Contact ID, Primary Number
  21. Table 3-5: Event Codes, Secondary Number
  22. Table 3-6: Event Codes, Secondary Number
  23. Table 3-7: Ademco Contact ID, Secondary Number
  24. Operating Instructions
  25. Displays
  26. Figure 4-1: ADT-UDACT Phone Connectors and LEDs
  27. Key Report Descriptions
  28. Disabling of Zones or Points
  29. Zone or Point Supervisory
  30. Figure 4-2: Handset/Speaker Connection
  31. Reporting Formats
  32. Table 5-2: Letter Code Definitions
  33. Table 5-3: Ademco Contact ID Reporting Structure
  34. Compatible Receivers
  35. Programming Reference Sheets
  36. Appendix B: Point Assignments (Unimode 300*/400)
  37. Appendix C: Point Assignments (ADT-MNNA)
  38. Appendix D: Unimode 2020/1010
  39. Figure D-3: EIA-485 Connection to Panel Mounted ADT-UDACT
  40. Figure D-4: EIA-485 Connection to Remote ADT-UDACT
  41. Appendix E: Unimode 300/400
  42. Figure E-3: Unimode 400 External ADT-UDACT Mounting in ADT-ABS8RF
  43. Appendix F: ADT-MNNA
  44. Appendix G: Annunciators
ADT ADT-UDACT Product Information Manual pdf 12 page image
Document 50934 Rev B 5/15/00 PN 50934:B12If the control panel causes harm to the telephone network, the telephone companyreserves the right to temporarily discontinue service. Advance notification will beprovided except in cases when advance notice is not practical. In such cases,notification will be provided as soon as possible. The opportunity will be given tocorrect any problems and to file a complaint.DO NOT CONNECT THIS PRODUCT TO COIN TELEPHONE, GROUND START,OR PARTY LINE SERVICES.When the control panel activates, premise phones will be disconnected.Two separate phone lines are required. Do not connect both telephone interfaces tothe same telephone line.The control panel must be connected to the public switched telephone networkupstream of any private telephone system at the protected premises.An FCC compliant telephone cord must be used with this equipment. This equipmentis designed to be connected to the telephone network or premises wiring using acompatible RJ31X male modular plug which is Part 68 compliant.1.9.1 Normal Mode:Normal mode is the standard mode of operation. In this mode, the ADT-UDACTmonitors host FACP status as well as monitoring telephone line voltage. The ADT-UDACT reports system status information to UL listed Central Stations. Informationtransmitted includes general alarm, trouble and supervisory. It also transmits eitherthe number of zones or points activated or the specific point(s) activated, dependingupon the compatible panel, programming selections and transmission formatselection. Specific system trouble conditions and specific ADT-UDACT troubles arealso transmitted.1.9.2 Program Mode:Program mode is used to program the ADT-UDACT. While the ADT-UDACT is inthe program mode, it cannot receive host FACP status information. See Section 3.0for complete programming instructions.1.9.3 Lamp Test Mode:This mode turns on all segments of the 4 character display plus all LEDs on the ADT-UDACT.1.9.4 Troubleshoot Mode:Troubleshoot mode may be used for testing the telephone line wiring. Connectionfrom the ADT-UDACT's modular jacks, through RJ31X jacks and into the telephonenetwork may be easily checked. In this mode, the keypad acts similar to a telephonetouchpad.1.9.5 Type Mode:Type Mode is used to define the specific type of device (point) used or function of azone. Type Mode is also used to disable the alarm report for any zone/point in thesystem. The feature which disables the zone/point alarm report must be used forzones/points programmed into the host FACP as remote silence, reset, drill oracknowledge switches. Note: Unimode2020/1010 and ADT-MNNA applicationsrestrict Type Mode programming to a maximum of 568 points. All remaining pointsabove 568 will report as fire alarm points only.1.9 Modes andSpecial Functions
/ 68
This manual is suitable for:
ADT-UDACT
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved