Keysight Technologies 34970A manuals

34970A

Brand: Keysight Technologies | Category: Switch

Table of contents

1. copyright notice
2. Software Updates/Licenses
3. Safety Symbols
4. Safety Considerations
5. Do Not Remove the Instrument Cover
6. Environmental Conditions
7. Regulatory Markings
8. Waste Electrical and Electronic Equipment (WEEE) Directive
9. The Front Panel at a Glance
10. The Front-Panel Menu at a Glance
11. Display Annunciators
12. The 34970A Rear Panel at a Glance
13. The 34972A Rear Panel at a Glance
14. The Plug-In Modules at a Glance
15. a multifunction module
16. In This Book
17. Table Of Contents
18. Table Of Contents
19. Table Of Contents
20. Table Of Contents
21. Table Of Contents
22. 1 Specifications
24. Quick Start Quick Start
25. To Prepare the Instrument for Use
26. To Connect Wiring to a Module
27. To Set the Time and Date
28. To Configure a Measurement Channel
29. To Monitor a Single Channel
30. To Close a Channel
31. quick start
32. If the Instrument Does Not Turn On
33. To Adjust the Carrying Handle
34. To Rack Mount the Instrument
35. Front-Panel Overview Front-Panel Overview
36. Front-Panel Menu Reference
37. To Unsecure for Calibration
38. To Secure Against Calibration
39. To Change the Security Code
40. Error Messages
41. To Perform a Zero Adjustment
42. To Apply Mx+B Scaling to Measurements
43. To Read the Relay Cycle Count
44. To Read a Digital Input Port
45. To Write to a Digital Output Port
46. To Read the Totalizer Count
47. To Output a DC Voltage
48. Calibration Procedures Calibration Procedures
49. Keysight Technologies Calibration Services
50. Time Required for Calibration
51. Recommended Test Equipment
52. Input Connections
53. Calibration Security
54. To Unsecure the Instrument Without the Security Code
55. Calibration Message
56. Calibration Procedure
57. Test Considerations
58. Performance Verification Tests
59. Self-Test
60. Quick Performance Check
61. Internal DMM Verification Tests
62. Gain Verification
63. Optional AC Performance Verification Tests
64. Internal DMM Adjustments
65. Gain Adjustment
66. VDC Adjustment Procedure (Optional)
67. Plug-in Module Test Considerations
68. Relay Verification
69. Optional) 34901A Relay Contact Resistance Verification
70. Optional) 34902A Relay Contact Resistance Verification
71. Optional) 34903A Relay Contact Resistance Verification
72. Optional) 34904A Relay Contact Resistance Verification
73. Optional) 34905/06A Relay Contact Resistance Verification
74. Optional) 34908A Relay Contact Resistance Verification
75. Thermocouple Reference Junction (Optional)
76. Thermocouple Reference Junction Adjustments
77. A Analog Output
78. Analog Output Adjustment
79. 5 Theory of Operation
80. Theory of Operation
81. System Block Diagram
82. Floating Logic
83. Memory
84. Earth-Referenced Logic
85. Power Supplies
86. Front Panel
87. Backplane
88. Internal DMM
89. Input
90. Input Amplifier
91. Ohms Current Source
92. AC Circuit
93. A-to-D Converter
94. Switch Modules
95. Switch Module Control
96. Relay Drivers
97. A/34906A
98. Multifunction Module
99. Totalizer
100. Analog Output
101. Digital I/O
102. Service Service
103. Operating Checklist
104. Types of Service Available
105. Repackaging for Shipment
106. Electrostatic Discharge (ESD) Precautions
107. To Replace the Power-Line Fuse
108. Self-Test Procedures
109. Disassembly
110. General Disassembly
111. Internal DMM Disassembly
112. Front Panel Disassembly
113. Additional Chassis Disassembly
114. Plug-In Module Disassembly
115. Recyclable Parts
116. Replaceable Parts