Xerox phaser 3635 Service Manual

Also see for PHASER 3635: User guide System administration guide Service manual

Contents

Xerox phaser 3635 Service Manual Manual pdf 23 page image

2-15Phaser 3635MFP 05-100, 05-500Status Indicator RAPsDraft 405-100 DADF Jam 1 RAP05-100 The lead edge of the document failed to actuate the scan sensor within the correct timeafter registration solenoid actuation.ProcedureWARNINGSwitch off the electricity to the machine. Disconnect the power cord from the customersupply while performing tasks that do not need electricity. Electricity can cause death orinjury. Moving parts can cause injury.NOTE: The door open switch must be actuated to supply +24V to the motors and solenoids.Refer to Wiring Diagram 10. Perform the following:1. Open the DADF door assembly, PL 5.10 Item 3. Remove all jammed paper.2. Check the document path for damage or obstructions.3. Check that the following components are clean and rotate freely:• Registration roll, PL 5.35 Item 9.• Registration roll idlers, PL 5.15 Item 8.4. Remove the transport assembly upper cover, PL 5.35 Item 13.5. Check that the DADF scan sensor actuator, PL 5.35 Item 6 moves freely and is not dam-aged.6. Enter dC330 code 05-140. Check the scan sensor (Q05-140), PL 5.35 Item 7. If neces-sary, install a scan sensor.7. Check the wiring between the DADF scan sensor and CN1 on the DADF PWB.8. Remove the DADF rear cover, PL 5.10 Item 9. Enter dC330 code 05-200. Check that theDADF scan motor, PL 5.40 Item 2 runs.9. Check the wiring between the DADF scan motor and CN9 on the DADF PWB.10. Open the DADF door assembly, PL 5.10 Item 3. Manually actuate the DADF door opensensor, PL 5.40 Item 13. While the DADF scan motor runs, stack the code 05-310 to ener-gize the DADF registration solenoid (SOL05-310). Check that the registration roll, PL 5.35Item 9 rotates.11. Check the wiring between the DADF registration solenoid and CN8 on the DADF PWB.12. If necessary, install new components:• DADF PWB, PL 5.15 Item 16.• DADF scan motor, PL 5.40 Item 2.• DADF registration solenoid, PL 5.40 Item 3.• DADF drive assembly, PL 5.40 Item 1.• Document transport assembly, PL 5.35 Item 14.05-500 DADF Jam 5 RAP05-500 The machine has detected that the DADF door assembly is open during run.ProcedureWARNINGSwitch off the electricity to the machine. Disconnect the power cord from the customersupply while performing tasks that do not need electricity. Electricity can cause death orinjury. Moving parts can cause injury.Refer to Wiring Diagram 10. Perform the following:1. Open the DADF door assembly, PL 5.10 Item 3. Remove all jammed paper.2. Remove all jammed paper from the DADF exit tray.3. Open the DADF door assembly, PL 5.10 Item 3. Check that the door open sensor actua-tor is not damaged.4. Enter dC330 code 05-160. Check the DADF door open sensor (Q05-160), PL 5.40 Item13.5. Check the wiring between the DADF door open sensor and CN5 on the DADF PWB. Ifnecessary, install a new DADF door open sensor, PL 5.40 Item 13.6. If necessary, install new components:• DADF PWB, PL 5.15 Item 16.• Document transport assembly, PL 5.35 Item 14.