OneStart

Menu

Unitek HF2/230 User Manual

Page 1 preview
Page 2 preview
Page 3 preview
Page 4 preview
Page 5 preview
Page 6 preview
Page 7 preview
Page 8 preview
Page 9 preview
Page 10 preview
Page 11 preview
Page 12 preview
Page 13 preview
Page 14 preview
Page 15 preview
Page 16 preview
Page 17 preview
Page 18 preview
Page 19 preview
Page 20 preview
Page 21 preview
Page 22 preview
Page 23 preview
Page 24 preview
Page 25 preview
Page 26 preview
Page 27 preview
Page 28 preview
Page 29 preview
Page 30 preview
Page 31 preview
Page 32 preview
Page 33 preview
Page 34 preview
Page 35 preview
Page 36 preview
Page 37 preview
Page 38 preview
Page 39 preview
Page 40 preview
Page 41 preview
Page 42 preview
Page 43 preview
Page 44 preview
Page 45 preview
Page 46 preview
Page 47 preview
Page 48 preview
Page 49 preview
Page 50 preview
Page 51 preview
Page 52 preview
Page 53 preview
Page 54 preview
Page 55 preview
Page 56 preview
Page 57 preview
Page 58 preview
Page 59 preview
Page 60 preview
Page 61 preview
Page 62 preview
Page 63 preview
Page 64 preview
Page 65 preview
Page 66 preview
Page 67 preview
Page 68 preview
Page 69 preview
Page 70 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. Table Of Contents
  4. CHAPTER 1: DESCRIPTION
  5. CHAPTER 2: GENERAL SET-UP
  6. Power Line Voltage, Current, And Wire Size Requirements
  7. HF2 Weld Transformer Electrical Specifications
  8. HF2 Welding System Maximum Secondary Loop Resistance
  9. HF2 Weld Transformer To Weld Head Connections
  10. CHAPTER 3: WELDING SYSTEM SET-UP
  11. Weld Head Set-Up
  12. Firing Switch Cable Connection
  13. Single Air Regulator Adjustment (Model 80 Series)
  14. Quick Start Programming Guide
  15. General Information
  17. Weld Head Valve Driver Connections
  18. Dual Air Regulator Adjustments
  20. electrical connections
  21. PLC Timing Diagram
  22. Non-Force Fired, Multiple Air Actuated Weld Head System
  23. CHAPTER 4: CONTROLS
  24. HF2 Weld Control - Rear Panel Inputs and Outputs
  25. Sensing Port - Connector Pin Assignments
  26. Foot Switch Connector
  27. Firing Switch Operation
  28. Opto Coupler Firing Switch - 3-Wire Connection
  29. Control Signals - Pin Assignments
  30. Control Signals - Remote Weld Schedule Selection Input
  31. Control Signals - Process Inhibit Input
  32. Air Valve 1 and Air Valve 2 Driver Connectors
  33. CHAPTER 5: PROGRAMMING MODES
  34. Basic Weld Monitor Run State
  35. Alarm State
  36. Program State
  37. Alphanumeric Program State
  38. Output Relays
  39. Relay 1 - Dual Air Head Operation
  40. Weld Functions
  41. Basic Weld
  42. Weld / Repeat
  43. Quench/Temper
  44. Pre/Postheat
  45. Up/Down Slope
  46. Braze
  47. Rollspot
  48. Seam
  49. Dual Pulse
  50. Pulsation
Unitek HF2/230 User Manual Manual pdf 1 page image
USER'S MANUAL 990-057Revision K, May 2004Use with Firmware Release V1.19 or higherMODEL HF22 kHz HIGH FREQUENCYRESISTANCE WELDING POWER SUPPLYMODEL NUMBER STOCK NUMBERHF2/230 1-264-03HF2/380 1-264-03-01HF2/460 1-264-03-02HF2/208 1-264-03-03HF2S/230 1-265-03HF2S/380 1-265-03-01HF2S/460 1-265-03-02HF2S/208 1-265-03-03Units with the built-in Weld Sentry Option also require User's Manual No. 990-291WARNINGPlease be sure to read all personnel and equipmentsafety precautions noted in this manual.
/ 70
Related manuals for Unitek HF2/208
Unitek UNIBOND 2 User Manual first page preview
Unitek UNIBOND 2 User Manual
Unitek UNIBOND II Operation, Maintenance And Service Manual first page preview
Unitek UNIBOND II Operation, Maintenance And Service Manual
This manual is suitable for:
HF2/208HF2/230HF2/380HF2/460HF2S/208HF2S/230HF2S/380HF2S/460
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved