Sealey STR002 Instruction Manual

InstructIon MAnuAL for:mobile TYRe RACKiNG SYSTem 200KGCAPACiTY PeR leVelMoDEL no: STR002thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions andproperly maintained, give you years of trouble free performance.1. SAFeTY iNSTRUCTioNSIMPORTANT: PleASe ReAD THeSe iNSTRUCTioNS CAReFUllY. NoTe THe SAFe oPeRATioNAl ReQUiRemeNTS, WARNiNGS & CAUTioNS.USe THe PRoDUCT CoRReCTlY AND WiTH CARe FoR THe PURPoSe FoR WHiCH iT iS iNTeNDeD. FAilURe To Do So mAY CAUSeDAmAGe oR PeRSoNAl iNJURY, AND Will iNVAliDATe THe WARRANTY. PleASe KeeP iNSTRUCTioNS SAFe FoR FUTURe USe.1.1 GeNeRAl SAFeTY WARNiNG! Ensure Health & Safety, and local authority regulationsare adhered to when assembling and using this racking system. Locate the racking in a suitable area where it will not be anobstruction. Keep the general area clean, uncluttered and ensure there isadequate lighting. WARNiNG! use the racking on a level and solid surface suchas concrete. Keep children and unauthorised persons away from the storagearea. Do NoT use the racking for any purpose other than that forwhich they are designed. Do NoT get the racking wet or use in damp or wet locations orareas where there is condensation. Do NoT clean the cross beams with any solvents which maydamage the coated surface. Do NoT overload the racking. Do NoT allow others to ride on the racking. Do NoT push loaded racking over edges, rough surfaces etc. asthe whole unit may overturn. Ensure that the racking is properly assembled before loadingwith heavy tyres. Maximum load for each level is 200kg. Load must be evenlydistributed. Place heavier items on the lower racks. Maintain correct balance and footing when moving the rackingand ensure that the floor surface is not slippery. Where possible heavier items should be evenly distributed acrossthe racks.3. CoNTeNTS2. iNTRoDUCTioNcarefully unpack the product and check the contents (fig.1)against the list below. should any items be missing or damaged,immediately contact your sealey dealer.Part Description............................................................ QuantityA upright .........................................................................................4b Horizontal Brace ..........................................................................8C Diagonal Brace ............................................................................4D spacer .........................................................................................4e castor* ........................................................................................4F Bolt M6 x 50mm ........................................................................14G nut M6 .......................................................................................26H safety Bolt M6 x 20mm .............................................................12i cross Beam.................................................................................6J Bolt M10 x 20mm ......................................................................16K nut M10 and spring Washer .....................................................16* 2 x swivel castors and 2 x fixed castors4. ASSemblY Warning! Before assembly and use ensure you have read,understood and apply Section 1 safety instructions.4.1 It is recommended that this tyre racking system be assembled bytwo people. When installing the cross beams it is advisable touse a rubber mallet. Do not use a hard faced hammer as this willdamage the surface finish of the cross beams. Make sure that allthe clips lock in place securely and safety bolts are fitted beforeusing the unit. Do not use any parts that are damaged and/ordistorted as these may assemble incorrectly and result in aninstallation that is unsafe and which may cause injury or damagewhen the shelves are loaded.three level mobile tyre rack system helps keep working area clear.unit is on wheels for easy manoeuvrability when needing to take thetyres to point of work, ideal for use track side. steel construction witha powder coated finish giving anti-corrosion resistance.Height: 1700mm Width: 915mm Depth: 455mmmaximum Capacity: 600kg (200kg/level)str002 IssuE 1 05/08/11Original Language Versionfig.1

/ 2

Related manuals for Sealey STR002