Sealey TC961 Instructions Manual

InstructIons for:WORKSHOP TYRE CHANGERSMoDEL no's: TC961, TC962thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructionsand properly maintained, give you years of trouble free performance.1. SAFETY INSTRUCTIONSIMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSEDAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.1.2 GENERAL SAFETY WARNING! Ensure Health & Safety, local authority, and generalworkshop practice regulations are adhered to when using thisequipment. Under Health and Safety Law, Employers and SelfEmployed Personnel have a legal duty to ensure Safe WorkingConditions for all employees and personel that may come intocontact with this equipment. In particular they must carry out aspecific risk and hazard assessment in the workplace to eliminateor reduce any risk found and must record, update and retainrecords of the results of this inspection. familiarise yourself with the applications, limitations and anypossible or potential hazards of the tyre changer. Maintain the tyre changer in good condition (use an authorisedservice agent). replace or repair damaged parts. Use genuine parts only.Unauthorised parts may be dangerous and will invalidate the warranty. WARNING! check regularly for damaged parts. Any part that isdamaged must be repaired or replaced before the equipment isnext used. Locate the tyre changer in a suitable work area, keep area clean andtidy and free from unrelated materials. Ensure that there is adequatelighting. WARNING! Use on a level surface, preferably concrete, towhich the tyre changer must be bolted. Keep the tyre changer clean for best and safest performance. Wear approved safety eye protection (standard spectacles are notadequate). Keep hands and feet well clear of the bead breaker. Maintain correct balance and footing. Ensure the floor is notslippery and wear non-slip safety shoes. remove ill fitting clothing. remove ties, watches, rings, and otherloose jewellery and contain and/or tie back long hair. Keep children and unauthorised persons away from the work area. DO NOT use the tyre changer for any purpose other than that forwhich it is designed. DO NOT operate the tyre changer if any parts are damaged ormissing as this may cause failure and/or personal injury. DO NOT allow untrained persons to operate the tyre changer. DO NOT stand on the tyre changer. DO NOT operate the tyre changer when you are tired or under theinfluence of alcohol, drugs or intoxicating medication.MODEL TC962 ONLY WARNING! Ensure correct air pressure is maintained and notexceeded. recommended maximum pressure 150psi (10.3 bar). WARNING! Disconnect the tyre changer from the air supply beforechanging accessories, servicing or performing any maintenance. Keep air hose away from heat, oil and sharp edges. check airhose for wear before each use, and ensure that all connectionsare secure. DO NOT yank the hose from the air supply. DO NOT direct air from the air hose at yourself or others. When not in use ensure the air supply is turned off.2. AIR SUPPLY - TC962 ONLYTC961 TC962Max. safe Working Pressure. . . . . . . . . . . . n/A. . . . . . . . . . . . .150psiMin. Wheel Diameter . . . . . . . . . . . . . . . 203mm. . . . . . . . . . . . 203mmMax. Wheel Diameter . . . . . . . . . . . . . . 460mm. . . . . . . . . . . . 460mmMin. Wheel Depth . . . . . . . . . . . . . . . . . . 40mm. . . . . . . . . . . . . 40mmMax. Wheel Depth . . . . . . . . . . . . . . . . . 203mm. . . . . . . . . . . . 304mmWorking Height . . . . . . . . . . . . . . . . . . . 640mm. . . . . . . . . . . . 815mm3. SPECIFICATIONS2.1. Ensure the air valve is in the "off" position before connecting tothe air supply.2.2. You will require an air pressure between 100 and 150psi.2.3.  WARNING! Ensure that the air supply is clean and does notexceed 150psi. too high an air pressure and/or unclean air willcause excessive wear and may cause damage and/orpersonal injury.2.4. Drain the air tank daily. Water in the air line will damage thetyre changer.2.5. clean the compressor air inlet filter screen weekly. therecommended hook-up is shown below.2.6. Line pressure should be increased to compensate forunusually long air hoses (over 8 metres). the minimum hosediameter should be 10mm I.D. and fittings must have the sameinside dimensions.2.7. Keep hose away from heat, oil and sharp edges. check hosesfor wear and make certain that all connections are secure.TC961TC962Original Language Version tc961, tc962 Issue: 2 - 20/10/09

/ 4

Related manuals for Sealey TC961