Samsung LN32A540P2DXZAOM User Manual

Also see for 5 Series: Quick setup guide Quick setup guide Quick setup guide Quick start guide User manual

English - 58Listening through a Receiver (Home theater)You can listen to sound through a receiver instead of the TV speaker.1. Press the TOOLS button.Press the ENTER button to select “Anynet+(HDMI-CEC)”.Press the ▲ or ▼ button to select "Receiver", then press the ENTER button.2. Press the ◄ or ► button to select to "On", then press the ENTER button.Now you can listen to sound through the receiver.3. Press the EXIT button to exit.If your receiver supports audio only, it may not appear in the device list.The receiver will work when you have properly connected the Optical IN jack of the receiver to the Optical Out jack of the TV.When the receiver (home theater) is set to On, you can hear sound output from the TV’s Optical jack. When the TV isdisplaying a DTV(air) signal, the TV will send out 5.1 channel sound to the Home theater receiver. When the source is a digitalcomponent such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home Theaterreceiver.When listening through the receiver, there are restrictions for using the PIP and audio-related (MTS, Preferred language)menus.If there is a power interruption to the TV when the “Receiver” is set to “On” (by disconnecting the power cord or a powerfailure), the “TV Speaker” may be set to “Off” when you turn the TV on again. (see page 30)Troubleshooting for Anynet +Symptom SolutionAnynet+ does not work. ■ Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+devices only.■ Connect only one receiver (home theater).■ Check if the Anynet+ device power cord is properly connected.■ Check the Anynet+ device’s Video/Audio/HDMI cable connections.■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.■ Check whether the TV remote control is in TV mode.■ Check whether it is Anynet+ exclusive remote control.■ Anynet+ doesn’t work in certain situations. (Searching channels, Plug & Play, etc.)■ When connecting or removing the HDMI cable, please make sure to search devicesagain or turn your TV off and on again.■ Check if the Anynet+ Function of Anynet+ device is set on.I want to start Anynet+. ■ Check if the Anynet+ device is properly connected to the TV and check if the Anynet+(HDMI-CEC) is set to On in the Anynet+ Setup menu.■ Press the TV button on the TV remote control to switch to TV. Then press the TOOLSbutton to show the Anynet+ menu and select a menu you want.I want to exit Anynet+. ■ Select View TV in Anynet+ menu.■ Press the SOURCE button on the TV remote control and select a device other thanAnynet+ devices.■ Press any of CH, CH LIST, PRE-CH, and FAV.CH to change the TV mode.(Note that the channel button operates only when a tuner-embedded Anynet+ deviceis not connected.)The message Connecting toAnynet+ device... appears on thescreen.■ You cannot use the remote control when you are configuring Anynet+ or switching to aview mode.■ Use the remote control when the Anynet+ setting or switching to view mode iscomplete.The Anynet+ device does not play. You cannot use the play function when Plug & Play is in progress.The connected device is notdisplayed.■ Check whether or not the device supports Anynet+ functions.■ Check whether or not the HDMI cable is properly connected.■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.■ Search Anynet+ devices again.■ You can connect an Anynet+ device using the HDMI cable only. Some HDMI cablesmay not support Anynet+ functions.■ If it is terminated by an abnormal situation such as disconnecting the HDMI cable orpower cord or a power failure, please repeat the device scan.The TV program cannot berecorded.Check whether the antenna jack on the recording device is properly connected.The TV sound is not outputthrough the receiver.Connect the optical cable between TV and the receiver.Recevier: OnConnect RecorderSetupAir28EnterMove Return