Samsung 5 Series Quick Setup Manual

Also see for OFFICESERV 500 Series: Service manual System administration guide Quick setup guide Quick setup guide Quick setup guide

Step 5: Run Plug & PlayWhen you turn on your TV for the first time, it automatically launches the Plug &Play function. With Plug & Play, you can select the On Screen Display language,set the clock mode, and launch the TV’s channel memorizing process.It also displays connection instructions similar to those in this guide.To navigate while Plug & Play is running, press the Up, Down, Left or Right arrowbuttons on your remote. To make a selection, press the ENTERE button.To skip a screen, press the MENU button. To turn on your TV, press the POWERbutton on the remote or on the TV. To run Plug & Play, follow these steps:1 Using your remote control,select the language for the OnScreen Display (OSD), and thenpress the ENTERE button.Plug & Play2 Select Home Use, and thenpress the ENTERE button. Ifyou select Store Demo, the TVwill reset your picture and audiosettings every 30 minutes.3 Select the Antenna Sourceto memorize. you must selectAntenna Source to same typeas your cable system type. Afterselecting source, select Start;then press the ENTEREbutton on your remote.Step 1: Install the StandFollow the steps below to connect the TV to the stand.✎ NOTEx Make sure to distinguish between the front and back of the Stand andGuide Stand when assembling them.x Make sure that at least two persons lift and move the LCD TV.x Stand the product up and fasten the screws. If you fasten the screws withthe LCD TV placed down, it may lean to one side.1 Connect the Guide Stand to theStand using four screws(M4 X L12) as shown.2 With your TV upright, connectthe TV to the Stand as shown.3 Fasten the two screws (M4 X L12) atposition 1, and then fasten the twoscrews (M4 X L12) at position 2.ssss12Step 2: Install the Batteries into the RemoteTo install batteries into your remote control,follow these steps:1. Lift the cover on the back of the remoteupward as shown in the figure to the right.2. Install two AAA batteries.✎ Make sure to match the + and -ends of the batteries to the diagramin the battery compartment.3. Replace the cover.Step 3: Connect Power and Antenna or CableQuick Setup GuideCongratulations on the purchase of your new Samsung TV.Read this setup guide to get your TV up and running quickly.1-800-SAMSUNG (1-800-726-7864)Samsung Electronics America, Inc.85 Challenger Road Ridgefield Park, NJ 07660-2112Samsung Electronics Canada Inc.55 Standish Court Mississauga, Ontario L5R 4B2Call Center hours of operation: Mon-Sun, 9:00 AM -12AM EST.To register this product, visit: www.samsung.com/register.STOPPlease do not return this unit.If you have problems operating yourTV, call:1-800-SAMSUNG (1-800-726-7864)For web support please visit:www.samsung.com/supportStep 4: Connect External DevicesConnecting an AV device (DVD/ Blu-ray player, cable/satellite boUse one of the connections below to connect your TV to an external A/V device. We reL Move E EnterSelect ‘Home Use’ when installing this TV in your home.Store Demo Home UsePlug & PlayU Move E Enter m SkipSelect the Antenna source to memorize.AirCableAutoStartStartStartPlug & PlayU Move E EnterSelect Language of the OSD.LanguageEnglishEspañolFrançaisPlug & PlayAUDIO OUTCOMPONENT OUTAUDIO OUT DVI OUTUsing an HDMI to DVI CableHD connection (up to 720p/1080i)Very Good ConnectionDeviceUsing a Component CableGood ConnectionComponent connection (up to 720p/1080i)DVD / Blu-ray player / HD Cable Box / HD Satellite receiver (STB)DeviceAudio Cable (Not Supplied)Component Cable (Not Supplied)Audio Cable(Not Supplied)HDMI to DVI Cable(Not Supplied)VHF/UHF AntennaConnect Ant In to• Wall cable jack• VHF/UHF Antenna• Cable or Satellite boxAnt or Cable OutMake sure the AC power cord is plugged in securely tothe wall outlet and the TV.Best to use 75 ohm (round) cable.orAntenna Cable (Not Supplied)Top viewFrontRearRearScrews (M4 X L12)Guide StandStandssssRearFront

/ 2

Related manuals for Samsung OFFICESERV 500 Series