Samsung 5 Series Quick Setup Manual

Also see for OFFICESERV 500 Series: Service manual System administration guide Quick setup guide Quick setup guide Quick setup guide

Quick Setup Guide1-800-SAMSUNG (1-800-726-7864)Samsung Electronics America, Inc.85 Challenger Road Ridgefield Park, NJ 07660-2112Samsung Electronics Canada Inc.55 Standish Court Mississauga, Ontario L5R 4B2Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST.To register this product, visit : www.samsung.com/register.Congratulations on the purchase of your new Samsung TV. Read thissetup guide to get your TV up and running quickly.STOPPlease do not return this unit.If you have problems operating yourTV, call:1-800-SAMSUNG (1-800-726-7864)For web support please visit:www.samsung.com/supportStep 4 : Connect External DevicesConnecting an AV device (Blu-ray player, cable/sateGetting StartedFor the very best picture quality, select HD signal sources and use HDMI cables andconnections. Note that many digital cable programs are not in HD. Check with your viprovider to ensure your are receiving HD signals.• Wall cable jack or• VHF/UHFAntenna or• Cable or Satellitebox Ant or CableOutStep 3 : Connect Power and Antenna or CableMake sure the AC power cordis plugged in securely to thewall outlet and the TV.Use a 75 ohm (round) cable.orStep 2 : Install the Batteries into the RemoteTo install batteries into your remote control, follow these steps:1. Lift the cover on the back of the remote upwardas shown in the figure to the right.2. Install two AAA batteries.Make sure to match the + and - ends of✎ the batteries to the diagram in the batterycompartment.3. Replace the cover.Connect AnT In to:Step 1 : Install the StandFollow the steps below to connect the TV to the stand.Make sure to distinguish between the front and back of the Stand and Guide✎ Stand when assembling them.Make sure that at least two people lift and move the LCD TV.✎ Lay the product down, with the screen facing up and fasten the screws.✎Power Input12Lowest Quality ConnectionUsing an Audio/Video CableVCR / DVD / Blu-ray player / Cable Box /Satellite receiverAudio/Video connection (480i only)VIDEO OUT VCR(HDD)USB1USB2 (HDD)USB1USB2 HDMI IN 4AV IN 2AUDIO OUTStep 5 : Run Plug & PlayWhen you turn on your TV for the first time, it automatically launches the Plug &Play function. With Plug & Play, you can select the On Screen Display language,set the clock mode, and launch the TV’s channel memorizing process. It alsodisplays connection instructions similar to those in this guide.To navigate while Plug & Play is running, press the Up, Down, Left or Rightarrow buttons on your remote. To make a selection, press the EnTErE button.To skip a screen, press the MEnU button.To turn on your TV, press the POwEr button on the remote or press thePOwEr button on the TV. To run Plug & Play, follow these steps:Select Language of the OSD.Language : EnglishU Move E EnterPlug & PlayEnglishEspañolFrançais1. On the Language screen, select the language for the On Screen Display(OSD) using your remote control, and then press EnTErE button. TheHome Use screen appears.2. Select Home Use, and then press EnTErE button. If you select StoreDemo, the TV will reset your picture and audio settings every 30 minutes. Afteryou press EnTErE button, the Antenna Source screen appears.3. If your TV is only attached to an antenna, select Air. If your TV is onlyattached to cable and you have no cable box, select Cable. If your TV isattached to an antenna and cable with no box, select Auto. When done,press EnTErE button on your remote. The Select Cable System screenappears.IMPORTANT: If your TV is attached to a cable or satellite box, skip Steps3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4,according to the directions for your cable or satellite box.ScrewStandAll manuals and user guides at all-guides.comall-guides.com

/ 2

Related manuals for Samsung OFFICESERV 500 Series