Panasonic th-49lf8w Operating Instructions Manual

Contents

Panasonic th-49lf8w Operating Instructions Manual Manual pdf 47 page image

47EnglishInput labelThis function can change the label of the Input signal tobe displayed.HDMI1HDMI2DVI-DPCVIDEOPCDVI-DHDMI2DIGITAL LINKCOMPONENT COMPONENTDIGITAL LINKHDMI1VIDEOInput label[HDMI1] [HDMI1] / [DVD1] / [DVD2] /[DVD3] / [Blu-ray1] / [Blu-ray2] /[Blu-ray3] / [CATV] / [VCR] /[STB] / (Skip)[HDMI2] [HDMI2] / [DVD1] / [DVD2] /[DVD3] / [Blu-ray1] / [Blu-ray2] /[Blu-ray3] / [CATV] / [VCR] /[STB] / (Skip)[DIGITAL LINK]*1 [DIGITAL LINK] / [DVD1] /[DVD2] / [DVD3] / [Blu-ray1] /[Blu-ray2] / [Blu-ray3] / [CATV] /[VCR] / [STB] / (Skip)[DVI-D] [DVI-D] / [DVD1] / [DVD2] /[DVD3] / [Blu-ray1] / [Blu-ray2] /[Blu-ray3] / [CATV] / [VCR] /[STB] / (Skip)[PC] [PC] / [DVD1] / [DVD2] /[DVD3] / [Blu-ray1] / [Blu-ray2] /[Blu-ray3] / [CATV] / [VCR] /[STB] / (Skip)[COMPONENT]*2 [COMPONENT] / [DVD1] /[DVD2] / [DVD3] / [Blu-ray1] /[Blu-ray2] / [Blu-ray3] / [CATV] /[VCR] / [STB] / (Skip)[VIDEO] [VIDEO] / [DVD1] / [DVD2] /[DVD3] / [Blu-ray1] / [Blu-ray2] /[Blu-ray3] / [CATV] / [VCR] /[STB] / (Skip)(Skip): When is pressed, the input will beskipped.*1: [DIGITAL LINK] is displayed for LF80 series only.*2: [COMPONENT] may be displayed as [RGB]depending on the settings of [Component/RGB-inselect]. (see page 44)Power management settingsSet each item to reduce power consump ion.Power management settingsPower management modeNo signal power offHDMI1 power managementHDMI2 power managementPC power managementDVI-D power managementPower saveCustomOffOffDisableOffOffOffDIGITAL LINK power management Off■ Power management mode: OnThe following fixed values are set to the menu ofpower consumption reduction. Individual setting is notavailable.[No signal power off]: [Enable][HDMI1 power management]: [On][HDMI2 power management]: [On][DIGITAL LINK power management]*: [On][DVI-D power management]: [On][PC power management]: [On][Power save]: [On]*: LF80 series only■ Power management mode: CustomThe menu of he power consumption reduction isindividually set. This setting is enabled when [Powermanagement mode] is set to [Custom].[No signal power off]When this is set to [Enable], the power supply of theunit goes off automatically when there is no operation orsync signal for about 10 minutes.Note● With the USB input, the unit determines no signal ispresent when the USB device is not connected.[HDMI1 power management][HDMI2 power management]When this function is set to [On], it operates underthe following conditions to turn the power on or offautomatically.When no pictures (sync signal) are detected for60 or so seconds at HDMI1 - HDMI2 input:Power is turned off (standby); the power indicatorlights up orange.When pictures (sync signal) are subsequentlydetected:Power is turned on; the power indicator lights upgreen.