Panasonic Viera TX-L32G20BA Operating Instructions Manual

Contents

Panasonic Viera TX-L32G20BA Operating Instructions Manual Manual pdf 13 page image

Auto SetupQuick StartGuide13(continued to the next page)3 Setup the wireless LAN connectionSetup the wireless LAN connection to enable the network service functions (p. 74).(If you do not wish to use wireless LAN connection or the network service functions, skip this step.)To setup the wireless LAN connection, the Wireless LAN Adaptor (optional accessory) is required. For the information about the Wireless LAN Adaptor “Optional accessories” (p. 6)Confirm the encryption key, settings and positions of your access point before starting setup. For details, read the manual of the access point.Please note that this TV does not support wireless public access points. To use a LAN cable instead of the Wireless LAN Adaptor p. 77Start wireless LAN connection setup?Please connect the wireless LAN adaptor (DY-WL10) to aUSB terminal.Yes Noconnect the Wireless LAN Adaptor to the USB 1 (rear) or 2 port (side)Wireless LAN Adaptor(optional accessory)Access pointInternetenvironmentaccessselect “Yes”You can setup the wireless LAN connection later“Network Setup” (p. 78)To skip this step EXITor select “No”Wireless LAN connection setup startsConnection TypePlease select network connection type.WPS(Push button)Search for access pointSelect the connection typeselectaccess If your access point supports WPS (Push button), then select this option.If not, select “Search for access point”.WPS(Push button) WPS(Push button)1) Please press the ‘WPS’ button on the accesspoint until its light flashes.2) When the light is flashing select ‘Connect’ on TV.If you are unsure, please check the instructionmanual of the access point.ConnectPress the WPS button on the access point until the light flashes.And then, press the OK button to connect the Wireless LAN Adaptor andthe access point.Ensure that your access point supports WPS for this setup. WPS: Wi-Fi Protected Setup TMSearch for access pointAccess points found automatically are listed.Available Access PointsAccess Point A 11n(2.4GHz)11n(5GHz)SSIDNo. Wireless type Encrypt ReceptionAccess Point BAccess Point C 11n(5GHz)123Select your desired access pointselectaccess: Encrypted access pointTo search access points again yellowFor the information of the highlighted access pointTo set manually (p. 79) redEncryption Key SettingConnection will be made with the following settings:-SSID : Access Point AAuthentication type : WPA-PSKEncryption type : TKIPPlease input the encryption key.Encryption keyAccess the encryption key input modeIf the selected access point is not encrypted, the confirmation screen will be displayed. It is recommended to select the encrypted access point.Access Point SettingsEncryption keyA B C D E F G H I J K L M NU V W X Y Z 0 1 2 3 4 5 6a b c d e f g h i j k l m nu v w x y z ( ) + - . * _O P Q R S T7 8 9 ! : #o p q r s t1.!:# 2abc 3def4ghi 5jkl 6mno7pqrs 8tuv 9wxyz0Enter the encryption key of the access pointSet characters one by one StoreselectsetBACK/RETURNYou can set characters by using numeric buttons. “Characters table for numeric buttons” (p. 95)Access Point SettingsEncryption key is set to:-XXXXXXXXSelect ‘Yes’ to confirm.Select ‘No’ to change.Yes NoSelect “Yes”selectsetTo re-enter the encryption key, select “No”.If the connection has failed, check the encryption key, settings and positions of your access point. And then, follow the on screen instructions.If connection to the access point is successful, we recommend you perform the “Connection Test” to confirm connection to the internet has been made. The “Connection Test” can be found in the NetworkSetup menu (p. 78).Exit to go to the next step