Panasonic TH-65PF50U Operating Instructions Manual

Also see for TH-60PF50U: Operating instructions

Contents

Panasonic TH-65PF50U Operating Instructions Manual Manual pdf 7 page image

7Safety PrecautionsWARNINGThe front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaningcloth or a soft, lint-free cloth.• If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in whichneutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until the surfaceis dry.• Do not scratch or hit the surface of the panel with fingernails or other hard objects, otherwise the surface may becomedamaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwisethe quality of the surface may be adversely affected.If the cabinet becomes dirty, wipe it with a soft, dry cloth.• If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been addedand then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.• Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets getinside the unit, operating problems may result.• Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the cabinetsurface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods in contactwith articles made from rubber or PVC.MaintenanceSetupDo not place the Plasma Display on sloped or unstablesurfaces, and ensure that the Plasma Display does nothang over the edge of the base.• The Plasma Display may fall off or tip over.Do not place any objects on top of the Plasma Display.• If water spills onto the Plasma Display or foreign objects getinside it, a short-circuit may occur which could result in fire orelectric shock. If any foreign objects get inside the PlasmaDisplay, please consult an Authorized Service Center.Do not cover the ventilation holes.• Doing so may cause the Plasma Display to overheat,which can cause fire or damage to the Plasma Display.Transport only in upright position!• Transporting the unit with its display panel facing upright ordownward may cause damage to the internal circuitry.If using the pedestal (optional accessory), leave a spaceof 3 15/16” (10 cm) or more at the top, left and right, and2 3/4” (7 cm) or more at the rear, and also keep the spacebetween the bottom of the display and the floor surface.If using some other setting-up method, follow the manualof it. (If there is no specific indication of installationdimension in the installation manual, leave a space of3 15/16” (10 cm) or more at the top, bottom, left and right,and 2 3/4” (7 cm) or more at the rear.)When installing the Plasma Display vertically;Turn up the power switch for the upward direction when youinstall the Plasma Display vertically.And set “DISPLAY ORIENTATION” to “PORTRAIT” inSETUP menu. (see page 46)An apparatus with CLASS I construction shall beconnected to a mains socket outlet with a protectiveearthing connection.AC Power Supply CordThe Plasma Display is designed to operate on 110 - 127V AC, 50/60 Hz.Ensure that the mains plug is easily accessible.Do not use any power supply cord other than thatprovided with this unit.• Doing so may cause fire or electric shocks.Securely insert the power cord plug as far as it will go.• If the plug is not fully inserted, heat may be generatedwhich could cause fire. If the plug is damaged or thewall socket plate is loose, they should not be used.Do not handle the power cord plug with wet hands.• Doing so may cause electric shocks.Do not do anything that might damage the power cable. Whendisconnecting the power cable, hold the plug, not the cable.• Do not make any modifications, place heavy objects on,place near hot objects, heat, bend, twist or forcefullypull the power cable. Doing so may cause damage tothe power cable which can cause fire or electric shock.If damage to the cable is suspected, have it repaired atan Authorized Service Center.If the Plasma Display will not be used for a long periodof time, unplug the power cord from the wall outlet.If problems occur during useIf a problem occurs (such as no picture or no sound),or if smoke or an abnormal odor is detected from thePlasma Display, unplug the power cord immediately.• Continuous use of the Display under these conditionsmight cause fire or permanent damage to the unit.Have the Display evaluated at an Authorized ServiceCenter. Services to the Display by any unauthorizedpersonnel are strongly discouraged due to its highvoltage dangerous nature.If water or foreign objects get inside the Plasma Display,if the Plasma Display is dropped, or if the cabinetbecomes damaged, disconnect the power cord plugimmediately.• A short may occur, which could cause fire. Contact anAuthorized Service Center for any repairs that need tobe made.