Menu
NEO HS2128 E User Manual
                                        | |
Contents
| 
Chapter 14.0 Regulatory Agency Statements14.0 Regulatory Agency StatementsFCC COMPLIANCE STATEMENTCAUTION: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, ifnot installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interferencewill not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-mined by turning theequipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Re-orient the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or experienced radio/television technician for help.The user may find the following booklet prepared by the FCC useful: “How to Identify and Resolve Radio/Television Interference Problems”. This booklet is availablefrom the U.S. Government Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4.The keypads represented in this manual can be used with the following Control Units: HS2016, HS2032, HS2064, HS2128.IMPORTANT INFORMATIONThis equipment complies with Part 68 of the FCC Rules and, if the product was approved July 23, 2001 or later, the requirements adopted by the ACTA. On the side ofthis equipment is a label that contains, among other information, a product identifier. If requested, this number must be provided to the Telephone Company.HS2016 Product Identifier US:F53AL01BHS2128HS2032 Product Identifier US:F53AL01BHS2128HS2064 Product Identifier US:F53AL01BHS2128HS2128 Product Identifier US:F53AL01BHS2128USOC Jack: RJ-31XTelephone Connection RequirementsA plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirementsadopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that isalso compliant. See installation instructions for details.Ringer Equivalence Number (REN)The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices notringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may beconnected to a line, as determined by the total RENs, contact the local Telephone Company. For products approved after July 23, 2001, the REN for this product is partof the product identifier that has the format US: AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). Forearlier products, the REN is separately shown on the label.Incidence of HarmIf this equipment (HS2016, HS2032, HS2064, HS2128) causes harm to the telephone network, the telephone company will notify you in advance that temporary dis-continuance of service may be required. But if advance notice is not practical, the Telephone Company will notify the customer as soon as possible. Also, you will beadvised of your right to file a complaint with the FCC if you believe it is necessary.Changes in Telephone Company Equipment or FacilitiesThe Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens theTelephone Company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.Equipment Maintenance FacilityIf trouble is experienced with this equipment (HS2016, HS2032, HS2064, HS2128) for repair or warranty information, contact the facility indicated below. If-the equip-ment is causing harm to the telephone network, the Telephone Company may request that you disconnect the equipment until the problem is solved. This equipment isof a type that is not intended to be repaired by the end user.DSC c/o APL Logistics 757 Douglas Hill Rd, Lithia Springs, GA 30122Additional InformationConnection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for inform-ation.Alarm dialing equipment must be able to seize the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment (tele-phone, answering system, computer modem, etc.) already has the telephone line in use. To do so, alarm dialing equipment must be connected to a properly installed RJ-31X jack that is electrically in series with and ahead of all other equipment attached to the same telephone line. Proper installation is depicted in the figure below. Ifyou have any questions concerning these instructions, you should consult your telephone company or a qualified installer about installing the RJ-31X jack and alarmdialing equipment for you.INDUSTRY CANADA STATEMENTNOTICE: The models: HS2016, HS2032, HS2064, HS2128 meet the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by theregistration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating thatIndustry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN assigned to each terminal equipment provides an indication of the max-imum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject onlyto the requirement that the sum of the Ringer Equivalence Numbers of all devices does not exceed 5.HS2016 Registration number IC:160A-HS2128HS2032 Registration number IC:160A-HS2128HS2064 Registration number IC:160A-HS2128HS2128 Registration number IC:160A-HS2128This product is in conformity with EMC Directive 2004/108/EC based on results using harmonized standards in accordance with article 10(5), R&TTE Directive1999/5/EC based on following Annex III of the directive and LVD Directive 2006/95/EC based on results using harmonized standards.This product meets the requirements of Class II, Grade 2 equipment as per EN 50131-1:2006 + A1:2009 Standard. This product is suitable for use in systems with the fol-lowing notification options:- A (use of two warning devices and internal dialer required),- B (self powered warning device and internal dialer required),- C (internal dialer and alternate IP/3G communicator required)- D (use of alternate IP/GSM communicator with encryption enabled required).The Model HS2016, HS2032, HS2064, HS2128Control Panel has been certified by Telefication according to EN50131-1:2006 + A1:2009, EN50131-3:2009, EN50131-6:2008 and EN50136-1:1997 for Grade 2, Class II,ATS2.FCC AND INDUSTRY CANADA STATEMENTS FOR WIRELESS KEYPADSModels: HS2LCDRF9, HS2LCDRFP9, HS2ICNRF9, HS2ICNRFP9 (operating in 912-919MHz band) are compliant with applicable FCC Part 15.247 and IC RSS-210 rules.WARNING! To comply with FCC and IC RF exposure compliance requirements, the HS2LCDRF(P)9 or HS2ICNRF(P)9 keypads should be located at a distanceof at least 20 cm from all persons duringnormal operation. The antennas used for this product must not be co-located or operated in conjunction with any other antenna or transmitter.- 35 - |
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved