Menu
NEO HS2128 E User Manual
                                        | |
Contents
| 
Chapter 14.0 Regulatory Agency StatementsThis device complies with FCC Rules Part 15 and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) Thisdevice may not cause harmful interference, and (2)this device must accept any interference that may be received or that may cause undesired operation.IC:160A – HS2KRFP9The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met.AVERTISSEMENT! Pour répondre aux exigences de conformité de la FCC et d’Industrie Canada sur les limites d'exposition aux radiofréquences (RF),les pavés numériques HS2LCDRF(P)9 ou HS2ICNRF(P)9 doivent être installés à une distance minimale de 20 cm de toute personne lors de leur fonctionnement usuel.Ces derniers ne doivent pas être situés au même endroit, ni être en fonction avec une autre antenne ou un autre transmetteur.Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditionssuivantes:(1)l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptibled'en compromettre le fonctionnement.Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditionssuivantes:(1)l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptibled'en compromettre le fonctionnement.GENERAL WARNINGThe following is a list of warnings applicable when this equipment is connected to the New Zealand Telecom Network. The grant of a Telepermit for any item of ter-minal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorse-ment of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects withanother item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom's network services.REVERSE NUMBERING (DECADIC SIGNALLING)Decadic signaling should not be used as it is being progressively phased out of the network. DTMF dialling is 100% available and it should always be used.LINE GRABBING EQUIPMENTThis equipment is set up to carry out test calls at pre-determined times. Such test calls will interrupt any other calls that may be set up on the line at the same time.The timing set for such test calls should be discussed with the installer. The timing set for test calls from this equipment may be subject to 'drift'. If this proves to beinconvenient and your calls are interrupted, then the problem of timing should be discussed with the equipment installer. The matter should NOT be reported as a faultto Telecom Faults Service.D.C.LINE FEED TO OTHER DEVICESDuring dialing, this device unit does not provide DC voltage to the series port connection.This may cause loss of memory functions for the terminal devices (local tele-phone) connected to T-1, R-1.General operation (ringer sensitivity and loading)This device only responds to Distinctive Alert cadences DA1 and DA2.In the event of any problem with this device, it is to be disconnected. A CPE item connected to one of the device’s terminal ports may be connected directly in itsplace. The user should then arrange for the product to be repaired. Should the matter be reported to Telecom as a wiring fault, and the fault is proven to be due to thisproduct, a call-out charge will be incurred.- 36 - |
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved