NEC MT1075 User Manual

Also see for MT1060 Series: Supplementary guide Control commands Command guide Command guide Control commands

Contents

NEC MT1075 User Manual Manual pdf 45 page image

E-41Masking Unwanted Area (Blanking)This feature allows you to mask any unwanted area of the screenimage.Adjust the Top, Bottom, Left or Right blanking with the SELECT or button.Adjusting Position and ClockThis allows you to manually adjust the image horizontally and verti-cally, and adjust Clock and Phase.Horizontal/Vertical Position:Adjusts the image location horizontally and vertically using the SE-LECT and buttons. This adjustment is made automatically whenthe Auto Adjust is turned on. See "Auto Adjust" on page E-47 forturning on or off the Auto Adjust feature.Clock .............. Use this item to fine tune the computer image or toremove any vertical banding that might appear. Thisfunction adjusts the clock frequencies that eliminatethe horizontal banding in the image.Press the SELECT and buttons until the band-ing disappears. This adjustment may be necessarywhen you connect your computer for the first time.This adjustment is made automatically when the AutoAdjust is turned on.Phase ............ Use this item to adjust the clock phase or to reducevideo noise, dot interference or cross talk. (This isevident when part of your image appears to be shim-mering.) Use the SELECT and buttons to adjustthe image.Use "Phase" only after the "Clock" is complete. Thisadjustment is made automatically when the Auto Ad-just is turned on.Selecting ResolutionThis allows you to activate or deactivate the Advanced AccuBlendfeature.Auto ............... Turns on the Advanced AccuBlend feature. The pro-jector automatically reduces or enlarges the currentimage to fit the full screen.Native ............. Turns off the Advanced AccuBlend feature. The pro-jector displays the current image in its true resolu-tion.See "Auto Adjust" on page E-47 for turning on or offthe Auto Adjust feature.NOTE:* When "Resolution" is set to "Native", "3D Reform", "Aspect Ratio", "Screen"and "Overscan" are not available.* While you are displaying an image with higher resolution than the projector'snative resolution, “Resolution” is not available.Selecting Overscan PercentageSelect overscan percentage (0%, 5%, 10% and 25%) for signal.NOTE: When "Resolution" is set to "Native", this feature is not available, andthe stored settings and adjustments are invalid.NOTE: When "4:3 Fill" or "Crop" is selected in "Aspect Ratio", this feature is notavailable.Selecting Video Filter Level (not available for Video, Viewer and LAN)This function reduces video noise.Off .................. The filter is removed.Less ............... The low-pass filter is applied partially.More .............. The low-pass filter is applied fully.Selecting Noise Reduction Level (not available for RGB, Viewer and LAN)Select one of the three levels for reducing video noise: Low, Mediumor High.NOTE: The lower the Noise Reduction level, the better the image quality byway of higher video bandwidth.Signal TypeSelect either the RGB signal type or the Component signal type.RGB ............... RGB signalComponent .... Component signals such as Y/Cb/Cr, Y/Pb/PrNOTE: This feature is available on RGB 1 and 2 only. If you do not get a betterpicture even when you set "Signal Select" to "Component" in Setup, set this to"Component".Picture ManagementThis option allows you to adjust neutral tint for yellow, cyan or magenta.There are 5 factory presets optimized for various types of images, oryou can set 4 user adjustable settings.Presentation .. Recommended for making a presentation using aPowerPoint filesRGB ............. Standard color valuesGraphic .......... Recommended for graphicsVideo ............. Recommended for regular picture such as TV pro-gramMovie ............. Recommended for movieUser 1-4 ......... User adjustableNOTE: When "sRGB", "Graphic", "Video" or "Movie" is selected, the brightnessdecreases slightly when compared to "Presentation". This is not a malfunction.User Adjust (when using User 1 to 4)When selecting one of four user adjustable presettings (User 1 through4), the submenu will be displayed.You can customize each gamma or color. To do so, first select [Set-ting] and press the ENTER button, and then proceed the followingsteps.