JVC LVT1306-007A Instructions Manual

Also see for RX-F31S: Instructions Service manual Service manual

Contents

17When your clapping sound is detected successfully,• On the TV screen, “SUCCESSFUL,” “RESULT,” and the settingvalues appear. The setting values are shown for about 10seconds.Ex.:• On the display, “SUCCESSFUL” appears, then the settingvalues are shown as follows for about 10 seconds:Ex.:*6 Standard channel (the closest speaker).This speaker position now works as the referenceposition (“0m/ft”) and other speakers’ distance isshown by the difference with this reference speakerposition.*7 Difference of each speaker position in distance (inmeters or feet).*8 Each speaker’s output level (–6 to +6).When finishing to show the setting values,On the TV screen, “COMPLETED” appears, then “TEST TONE”and “END” appear. On the display, “TEST? END?” appears.• To adjust the speakers’ output levels manually, press TESTTONE (see page 29).• To disappear the on-screen display, press SET or any buttonexcept TEST TONE.• The receiver returns to normal operation mode automatically ifno operations are done for about 10 seconds.Ex.:When your clapping sound is not detected correctly,“SETTING UP” appears again after one of the followingmessages. In this case, repeat step3.SILENT: • The receiver detects sound from only the leftand right front speakers.• The receiver detects no sound from the frontspeakers and detects sound from at least one ofother speakers.SILENT-ALL: The receiver cannot detect any sound from anyspeaker for about 10 seconds.AGAIN: • The receiver cannot detect sound from the leftor right front speaker.• The receiver fails to calculate the speakers'output level and difference of each speaker'sposition in distance.In the following cases, set the speakers manually.• When “SILENT” appears twice in succession.The setting is partially made. (The distance of the speakersfrom which sound has not been detected is set to “+9.0m(+30ft).”)The receiver exits from Smart Surround Setup.• When “MANUAL” appears.The receiver fails to detect the sound three times. The receiverexits from Smart Surround Setup.To cancel Smart Surround Setup, press SMART SURROUNDSETUP while “SETTING UP” flashes.• No other operations can be accepted after “SETTING UP” stopsflashing. Complete the Smart Surround Setup.To check the current setting made by Smart Surround Setup,press SMART SURROUND SETUP while the receiver is innormal operation mode.The setting values appear. On the display, the setting values areshown one after another.• The current setting is not indicated but “MANUAL” appears if youchange the following settings after using Smart Surround Setup:– If you change speaker distance manually.– If you change one of the speaker sizes either from “NO” to“SMALL” or “LARGE,” or from “SMALL” or “LARGE” to “NO.”To check the current setting, see each setting item of thespeaker distance (see page 22) and the speaker output level(see page 29).• If you have not used Smart Surround Setup, “NO S.S.S.”appears.NOTES• The speaker distance and output level manually set will beapplied instead of those set by using Smart Surround Setup inthe following cases:– When you change one of the speaker distances (see page22).– When you change one of the speaker sizes either from “NO”to “SMALL” or “LARGE,” or from “SMALL” or “LARGE” to “NO”(see page 21).• When you want to adjust the speaker distance and output levelmanually, see pages 22 and 29.• When the headphone is in use or “DVD MULTI” is selected asthe source, the receiver returns to normal operation modewithout showing “TEST TONE.”• The speakers which are set to “NO” in the speaker setting (seepage 21) are not indicated clearly on the TV screen.• Do not clap your hands so hard that it may hurt your hands.SMART SURROUND SETUPL+2 C 0 R+2+0.3m STD+0.3mSUCCESSFULRESULTLS+4 RS+4+0.6m +0.6m*6*7*8*6*7 *8LR RS LSCSMART SURROUND SETUPL+2 C 0 R+2+0.3m STD+0.3mTEST TONEENDLS+4 RS+4+0.6m +0.6m