Cisco TelePresence System Profile 52” Dual Installation Sheet

Also see for TelePresence: Quick reference guide Administration guide Brochure Specifications Administrator's guide

Installing Cisco TelePresence System Profile 52” DualPage 178-19776-01revB Profile 52 Dual Installation Sheet | April 2012 | © 2010-2012 Cisco Systems, Inc. All rights reserved.PRECAUTIONSPlease follow the steps in this installation guide when unpacking andassembling Profile 52” Dual.MANPOWERA minimum of two (2) persons are required when installingProfile 52” Dual.UNPACKING THE SYSTEM AT THE DESTINATIONIt is highly recommend to start the unpacking and assembling ofProfile 52” Dual at the place where it is to be used.If it is not possible to bring the complete delivery to the room whereProfile 52” Dual is to be used, then unpack and bring the smaller unitsto the destination.• The monitor box requires two (2) persons to lift 55 kg / 121 lb).• The bottom module column requires two (2) persons to lift(40 kg / 88 lb).• The foot module requires two (2) persons to lift(stand-alone: 35 kg / 77 lb; wall-mounting: 20 kg / 44 lb).INSTALLATION NEAR A SOCKET-OUTLETThe equipment must be installed near a socket-outlet. The socket-outlet shall be easily accessible after installation.ROOM GUIDELINESNOTE: The floor must be in level.The recommended distance between the Profile 52” Dual and themeeting room table should be minimum 1.5 m / 59 in.Read more about room guidelines in the Video conferencing roomprimer.USER DOCUMENTATIONThe user documentation for this product, including compliance andsafety information, is available on the Cisco web site.Go to: http://www.cisco.com/go/telepresence/docs.DIMENSIONS OF THE PROFILE 52” DUAL• Height: 63.8” / 162 cm• Width: 94.9” / 241 cm• Depth (wall mounting): 10.2” / 26 cm• Depth (stand-alone): 17.7” / 45 cm• Weight: 518 lb / 235 kgThe Profile 52” Dual delivery contains:Monitor box:• Two monitors andspeaker grillesBottom module columnCameraTouch Screen CSFoot module box:• Foot module (stand-alone or wallmounting)• Four M8×45 screws• Two wall mounting brackets and fourM6×10 screws (for wall mounting only)• Wrench• Level adjustment tool (orange)Monitor back cover box:• Monitor back cover• Monitor brackets• M4×25 and M4×8 screws for the monitorbrackets• Camera bracket• Wing nuts for the camera bracketAccessories box:• Cables• Microphones, 4 pcs• Remote control and 4 AAA batteries• Gloves, 2 pairs• Cleaning cloth• Allen key, screwdriver• Four M8×16 screws1 Content overviewRemove the outer cover and locate the different boxes as illustrated below.2 Lift the column out of the package. Mount the column to the footmodule to complete the bottom moduleLeft monitorRight monitorColumnStand-alonefoot moduleCAUTIONHEAVY3 WHEN YOU HAVE A WALL MOUNTING FOOT MODULE:Mount the column to the foot module and fasten it to the wall WARNINGDue to the size and weight of this equipment, it is veryimportant that the wall mount unit is safely installed accordingto the installation instructions and that the wall is able to safelysupport the product. It is highly recommended that the wallmounted system is installed by trained personnel.1. Mount the column to the wall mounting foot module, similar to step 2.2. Fasten the wall brackets to the bottom module with the four M6×10 screws.Use the Allen key.3. Place the bottom module by the wall, mark where to fasten the bracket andmove the bottom module away.4. Add the suitable fixing device for the screws in the wall, and fasten thebottom module.FASTEN THE COLUMN TO THE FOOT MODULE1. Make sure the foot module has been placed at its permanent location.2. Place the column on the foot module, open the rear door, and remove the doorstop bracket.3. Carefully open the rear door completely.4. Use four M8×45 screws and fasten the column to the foot module.5. Mount the door stop bracket back in place.LEVELLING ADJUSTMENTMake sure the unit is stable.Place the orange level adjustment tool on thefoot wheel under the foot module for heightadjustment.Seen from above, turn clockwise to adjust theheight up. Use the opposite side of the tooland turn counterclockwise to adjust down.Grab here whenlifting the column.CAUTIONHEAVYCAUTIONHEAVYRev. Date Prep. Checked Change---Telecom AS ------------------Part weight:Sheet size:Scale:Surface treatmentSpecification: MaterialTolerancesUnit:EuropeanprojectionSheet 1 of 1All materials, finishes, and proccessesmust comply with the RoHS directivesDimensions without paint or finishFlame class requirement: -ProcessesType:Manufacturer:Type number:Thickness:Color:Surface:Glossiness:Flame class:UL reference:3D CAD model file 120601 rev. 03 is masterPackaging Kit Profile 52" Dual120601 rev.71743gA3mm1:8Monitor back cover and monitor bracketsRight and left monitorBottom module columnCameraFoot moduleAccessories box 4 * M8×45Allen keyTouch screenUse the wrench to remove the doorstop bracket on the rear door beforefastening the column to the foot module.Rear sideDoor stop bracketFasten the columnto the foot module.Fasten the columnto the foot module.Access the innermost screws from these holes.The bottom module is viewed from the rear side.Add the suitable fixing device for the screws in the wall.The wall4 * M6×10Allen keyThe monitors come in a separate box. The monitor box contains monitors and speaker grillesfor the monitors. Remove the lid and locate the left and right monitor and the speaker grilles.Unpacking and assembling Profile 52” DualCAUTIONHEAVYEMC A Class declaration

/ 2

Related manuals for Cisco TelePresence