Cisco TelePresenceSX10 Quick SetINSTALLATION GUIDE78-100213-04A0 | JUNE 2018© 2018 Cisco Systems, Inc. All rights reserved.

remote control

Cisco TelePresence SX10 Installation Manual

TelePresence SX10

best practice

tour the touch screen

log onto a system with your own credentials

Edit a Contact List Entry, then Place the Call

place call using name

place call using an ip address

place call using number

receive call

receive call while in another call

Transfer

consult and transfer

disconnect yourself from call

a few words on microphone behavior and privacy

put call on hold and resume a call on hold

change call rate

enable do not disturb

enable standby

view keypad while in a call

add additional participants to existing call

add incoming call to existing call

view meeting participant list

manage conference call layout

lock speaker

disconnect participant from call

Intelligent Proximity

Activate and Deactivate Intelligent Proximity

getting started

Change Presentation Layout In a Call

presentation outside calls

view meeting list

join scheduled meeting

parallel meetings

Contacts Directory

call recents

Favorites

Add Someone to Favorites, While in a Call

view camera settings

add camera position preset

edit existing camera position preset

speaker tracking

Snap to Whiteboard

PresenterTrack

control own camera

manage selfview

resize the selfview pip

move the selfview pip

control the camera of the other participant

gain access to the settings

Ringtone & Sound

camera control

main source selection

Display

select language

system information

call status

diagnostic mode

restart system

about administrator

Administrator Settings—Tracking

Administrator Settings—Set Date and Time

Administrator Settings—Call Details

Administrator Settings—Provisioning Wizard

Administrator Settings—Multipoint Mode

Administrator Settings—Pairing

Administrator Settings—IP & VLAN, Codec

Administrator Settings—Network Status Codec

Administrator Settings—IP & VLAN, Touch

Administrator Settings—Network Status Touch

Administrator Settings—SIP

Administrator Settings—H323

Administrator Settings—EMC Resilience Mode

Administrator Settings—Factory Reset

user guide

tour the screen and the remote control

video calls

Edit a Contact List Entry Status, then Place the Call

Place Call Using Name, Number or Video Address

change the layout of the screen

Share Content Start and Stop Presentation

scheduled meetings

Contacts Make Someone a Favorite—Outside a Call

Make Someone a Favorite—While In a Call

Change the Position of a Picture-in-Picture on the Screen

far end camera control

Produced: December 2014 for TC 7

Best Practice

Tour the Touch Screen

Log Onto a System with Your Own Credentials

Place Call Using Name

Place Call Using an IP Address

Place Call Using Number

Receive Call

Receive Call While in Another Call

Consult and Transfer

Disconnect Yourself From Call

A few words on microphone behavior and privacy

Put Call on Hold and Resume a Call on Hold

Change Call Rate

Enable Do Not Disturb

Enable Standby

View Keypad While in a Call

Add Additional Participants to Existing Call

Add Incoming Call to Existing Call

View Meeting Participant List

Manage Conference Call Layout

Lock Speaker

Disconnect Participant from Call

Share Content Start and Stop Presentation in a Call

Presentation Outside Calls

Scheduled Meetings View Meeting List

Join Scheduled Meeting

Parallel Meetings

Call Recents

View Camera Settings

Add Camera Position Preset

Edit Existing Camera Position Preset

Speaker Tracking

Control Own Camera

Manage Selfview

Resize the Selfview PiP

Move the Selfview PiP

Control the Camera of the Other Participant

Settings Gain Access to the Settings

Camera Control

Main Source Selection

Select Language

System Information

Call Status

Diagnostic Mode

Restart System

Administrator

Introduction

User documentation and software

What's new in CE9

SX10 Quick Set at a glance

Power On and Off

LED indicators

How to administer the video system

Configuration

User administration

Change the system passphrase

Set a PIN code for the Settings menu

System configuration

Add a sign in banner

Manage the service certificates of the video system

Manage the list of trusted certificate authorities (CAs)

Set up secure audit logging

Manage pre-installed certificates for CUCM via Expressway provisioning

Delete CUCM trust lists

Change the persistency mode

Set strong security mode

Set up Intelligent Proximity for content sharing

Adjust the video quality to call rate ratio

Packet loss resilience - ClearPath

Choose wallpaper

Choose a ringtone and set the ringtone volume

Manage the Favorites list

Peripherals

Extend the number of input sources

Information about displays

Connect the Touch 10 controller

Maintenance

Upgrade the system software

Add option keys

System status

Run diagnostics

Download log files

Create a remote support user

Backup or restore a configuration

Revert to the previously used software image

Factory reset the video system

Factory reset the Touch 10

Capture user interface screenshots

System settings

Overview of the system settings

Audio settings

CallHistory settings

Cameras settings

Conference settings

FacilityService settings

H323 settings

Logging settings

Network settings

NetworkServices settings

networkservices https ocsp mode

networkservices ssh mode

Peripherals settings

Phonebook settings

Provisioning settings

provisioning externalmanager protocol

Proximity settings

RoomAnalytics settings

RTP settings

Security settings

security session showlastlogon

SerialPort settings

Cisco TelePresence SX10 Installation Manual

Product

Learn More

Legal


Contents remote control	Cisco TelePresenceSX10 Quick SetINSTALLATION GUIDE78-100213-04A0 \| JUNE 2018© 2018 Cisco Systems, Inc. All rights reserved. Next / 8