Cisco TelePresence System Profile 65" Installation Manual

Also see for TelePresence: Quick reference guide Administration guide Brochure Specifications Administrator's guide

Installing Cisco TelePresence System Profile 65”Page 178-19779-02 Profile 65 Installation Sheet | April 2012 | © 2010-2012 Cisco Systems, Inc. All rights reserved.1 Unpacking the foot module4 Key lock and levelling adjustment3 Mounting the column to the foot module to complete the bottom moduleMOUNTING THE BOTTOM MODULE1. Lift the column and place it carefullyon the foot module.2. When looking down through thecolumn you can see the four screwsin the foot module.Make sure the screws enter thecorresponding holes in the column.3. Open the front door to access thescrews. Secure the column to thefoot module with four nuts. The nutsare found in the plastic bag. See theillustration to the right.When the bottom module is finished,the hole in the foot module should bevisible on the rear side only.PERSON 1:Lift here.PERSON 2:Lift here.The illustration shows the stand-alonefoot module. The wall stand foot moduleis mounted in the same way.2 Unpacking the unitPRECAUTIONSFollow the steps in this installation guide when unpacking andassembling the Profile 65”.A minimum of four (4) persons are required during the installation of thesystem.• The monitor box requires four (4) persons to lift.• The column requires two (2) persons to lift.• The foot module requires two (2) persons to lift.NOTE: The floor must be in level.WEIGHTS Of THE DIffERENT UNITS (PACKAGING INCLUDED)• Monitor box: 110 kg / 243 lbs• Column: 40 kg / 88 lbs• Foot module box: 25 kg / 55 lbs• Accessories, camera, Touch 8” and grille boxes: 8 kg / 17.6 lbsUNPACKING THE SYSTEM AT THE DESTINATIONIt is highly recommended to start the unpacking and assembling ofProfile 65” at the place where the system is to be used.Check the dimensions of the lift if you need to use a lift for thetransportation.Outer dimensions and total weight of the main unit (package included):• Height: 145 cm / 57.1 in.• Width: 76 cm / 29.9 in.• Length: 170 cm / 66.9 in.• Weight: 183 kg / 402 lbsNOTE: If it is not possible to bring the main unit to the destination,follow step 1–2 and bring the smaller units to the destination.DIMENSIONS (WHEN ASSEMBLED)The Profile 65” system has the following dimensions:• Height: 167 cm / 65.7 in.• Width: 153 cm / 60.3 in.• Depth: Stand-alone: 66 cm / 26 in.Wall stand, with short bracket: 44.7 cm / 17.6 in.Wall stand, with long bracket: 52.2 cm / 20.6 in.USER DOCUMENTATIONUser guides and compliance and safety information for this product areavailable on the Cisco web site: http://www.cisco.com/go/profile-docsThe Video conferencing room primer and Video conferencing roomacoustics guidelines documents contain information about optimizing ameeting room for video conferencing.PROfILE 65” IS DELIvERED WITH:MonitorColumnFoot module (stand-alone or wall stand)GrilleCameraTouch 8” interface deviceRemote controlMicrophonesAccessoriesfOOT MODULE (25 kG / 55 LbS)1. Open the snap lockers2. Lift out the foot module boxMONITOR bOX(110 kg / 243 lbs)CAUTIONHEAvYANDBULKYREQUIRES:4 PEOPLE TO LIfTCAUTIONHEAvYANDBULKYREQUIRES:2 PEOPLE TO LIfTSTAND-ALONE FOOT MODULEWALL STAND FOOT MODULEACCESSORIES TO THE fOOT MODULE• Orange level adjustment tool• 4 × Nuts• Wall brackets (wall stand only)• Spacer (wall stand only)• Allen key (wall stand only)COLUMN(40 kg / 88 lbs)ACCESSORIES BOX• Power cables• Microphones• Remote control• batteries• Wrench• key lock tool• Gloves• Cleaning clothThe illustration showsa cross section ofthe bottom module(column and footmodule).Fasten the 4 nuts(two on each sideof the system).Outer coverCamera boxGrille boxAccessories boxFoam to protectthe columnColumnMonitor box1. Place the unit on a stable surface.2. Open the snap lockers to removeouter cover.3. Locate the different parts.4. Lift out the camera, Touch 8”,grille and accessories boxes.5. Remove the packaging above andaround the column and monitorbox.Lift out to openthe snap lockers.KEY LOCKPlace the orange key on the keylock and turn clockwise to lock,counterclockwise to unlock.The level adjustment tool is found inthe foot module box. The key locktool is found in the accessories box.ADJUST UPPlace the level adjustment tool asillustrated. Seen from above, turnclockwise to adjust the height up.ADJUST DOWNPlace the level adjustment tool atthe opposite side of the wheel.Turn counterclockwise to adjustthe height down.LockUnlockTouch 8” boxCAUTIONHEAvYLift out to openthe snap lockers.Front-Eagle117000 rev.rev. 00Z+ is master3D CAD model file 117000 -Telecom AS-----UL reference:ProcessesFlame class requirement: -Dimensions without paint or finishFlame class:must comply with the RoHS directivesSheet 1 of 1All materials, finishes, and proccessesprojectionUnit:1:10Tolerances MaterialSpecification: Surface treatmentScale:Sheet size:mmA4Part weight: 108964gEuropeanGlossiness:Surface:Color:Thickness:Type number:Manufacturer:-----Type: ---------Rev. Date Prep. Checked ChangeRev. Date Prep. Checked Change-Eagle117000 rev.rev. 00Z+ is master3D CAD model file 117000 -Telecom AS-----UL reference:ProcessesFlame class requirement: -Dimensions without paint or finishFlame class:must comply with the RoHS directivesSheet 1 of 1All materials, finishes, and proccessesprojectionUnit:1:10Tolerances MaterialSpecification: Surface treatmentScale:Sheet size:mmA4Part weight: 108964gEuropeanGlossiness:Surface:Color:Thickness:Type number:Manufacturer:-----Type: ---------FrontFront

/ 4

Related manuals for Cisco TelePresence