Black & Decker Workmate 425 TYPE 5 Manual

Also see for Workmate 425 TYPE 5: Instruction manual User manual

INSTALLING THE MIDDLE JAW11. With front jaw cranked to the front of the work center, insert the indexing lugs of themiddle jaw into the front keyholes. Rear jaw is then installed in the back keyholes. Turncrank handle clockwise to tighten. (Fig 10)SWIVEL PEGS12. The four supplied swivel pegs can be used in any of the holes in the front and rear jaws.The pegs are used to extend the size of your Workmate’s holding capacity. (Fig 11)WARNING: Read and understand all instructions. Failure to follow all instructionslisted below may result in serious personal injury.1. Do not load with more than 550 pounds.2. Do not apply an unbalanced load which could cause the work center to tip over.3. Do not use the work center as a stepladder or standing platform. Do not use the lowerplatform as a step when the work center is in “Workbench” position. The footboard is afoot REST only.4. Do not store work center outdoors or in a damp location.5. Avoid applying excessive force when clamping with the swivel pegs.6. Be sure that the legs are fully open (for workbench height) and be sure that the tablelocks in position.7. When using a power tool with the work center, follow the safety instructions in thetool’s instruction manual.8. Always wear safety glasses when operating power tools.9. An even pressure of the vise jaws on the workpiece is essential. Tighten both crankhandles uniformly.10. When assembling your work center, use only the special plastic socket wrenchprovided. Use of other wrenches or sockets can damage your work center.SAVE THESE INSTRUCTIONS FOR FUTURE USE.ASSEMBLY1. The Workmate ®425 work center comes partially assembled. Empty the cartoncompletely onto the floor and identify all the components. (Fig. 1)2. Assemble two top blocks to the underside of the rear jaw by fitting the raised posts onthe top blocks into the smaller holes of the rear jaw. Insert bolts through the rear jawand into top blocks and tighten with supplied wrench. (Fig. 2)3. Assemble top blocks to middle jaw the same as rear jaw. (Fig. 3)4. Remove the white clip from the end of each vise screw and discard. (Clip is forprotection of part only.)5. Aligning the hole in the vise crank with the hole in the vise screw, push the vise crankonto the vise screw end (protruding from the front of the vise jaw bracket). Using ahammer, drive the supplied pin into the aligned holes. Repeat this procedure for theinstallation of the other vise crank. (Fig. 4)6. Complete the assembly by pushing the snap-in knobs into the holes in the vise cranks.(Fig. 5)7. Install the front vise jaw on top of the top blocks so that the small holes at each end ofthe vise jaw fit down over the posts on the top side of the blocks. With the jawpositioned as described above insert into the frame as shown in figure 6. Insert a boltinto the holes in the jaw and tighten them securely into the holes in the pivot nut. Usethe socket wrench provided.8. Tip the front of the Workmate® up and rest it against your knee as shown in Fig. 7. Pullupwards on both left and right release levers to unlock Workmate® (Fig. 7a). Using bothhands, push the top of the Workmate® up and away from you while holding the footrestwith your other hand until the frame locks in place. (Fig.7b) Note: New Workmate® arestiff and require more effort to raise into the locked working position. To close theWorkmate® for storage, pull upward on the two release levers to unlock theWorkmate®. While holding the levers up pull back and down to close the Workmate®.(Fig.7c)FEATURES & APPLICATIONSVERTICAL CLAMPING9. Pull vertical locking bar toward yourself and lift front vise jaw until it is in vertical, lockedposition Note: Rear jaw must be in middle “keyhole” position. (Fig. 8)CHANGING THE INDEXED POSITION OF THE REAR JAW10. Install rear jaw in one of three possible indexed “keyhole” positions by inserting theindexing lug into a keyhole in the vise jaw bracket. Secure the rear jaw by moving rearjaw to the back of the key hole. (Fig. 9)VEA EL ESPAÑOL EN LA CONTRAPORTADA.SAVE THIS MANUAL FOR FUTURE REFERENCE.INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.Cat No. WM425 Type 5 Form # 632231-00 (APR-05)Copyright © 2005 Black & Decker Printed in ChinaBEFORE RETURNING THIS PRODUCTFOR ANY REASON PLEASE CALL1-800-54-HOW-TO (544-6986)IF YOU SHOULD EXPERIENCE A PROBLEMWITH YOUR BLACK & DECKER PRODUCT,CALL 1-800-54-HOW-TO (544-6986)BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No., TYPE No., ANDDATE CODE. IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN RESOLVE YOURPROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOURFEEDBACK IS VITAL TO BLACK & DECKER.REAR JAWMÂCHOIRE ARRIÈREMORDAZA TRASERAMIDDLE JAWMÂCHOIRE CENTRALEMORDAZA MEDIAFOLDING LEGSPIEDS ESCAMOTABLESPATAS PLEGABLESFOOTREST (NO STEP)REPOSE-PIED (PAS UN MARCHE-PIED)DESCANSO PARA LOS PIES (NO ESCALON)CRANKMANIVELLEMANIVELAFRONT VISE JAWMÂCHOIRE AVANTMORDAZA FRONTALVERTICAL LOCKING BARBARRE DE VERROUILLAGEVERTICALEBARRA DE FIJACION VERTICALSNAP-IN KNOBSBOUTONS ÀENCLENCHEMENT RAPIDEMANGOS DE LA MANIVELARELEASE LEVERLEVIER DE DÉGAGEMENTPALANCA DE LIBERACIÓNWorkmate®425 TYPE 54 Swivel Pegs4 mordaches orientables4 Topes giratorios2 Snap-in Knobs2 poignées de manivelle2 Perillas a presión6 Bolts6 boulons6 TornilosWrenchCléLlave4 Top Blocks4 blocs supérieurs4 Bloques superiores2 Cranks2 manivelles2 Manivelas2 Pins2 tiges2 PernosWorkmate FrameChâssis de l'étau-établiEstructura3 Jaws3 mâchoires3 mordazas2 front Blocks2 blocs avant2 bloques frontales2 Vise Screws2 tiges filetées2 Tornillos de prensa2 Pivot Nut2 écrous de pivot2 Tuercas de giroFig.1Fig. 2Fig. 3Fig. 4Fig. 5 Fig. 6Fig. 8 Fig. 9Fig. 10Fig. 11SERVICE INFORMATIONAll Black & Decker Service Centers are staffed with trained personnel to provide customerswith efficient and reliable power tool service. Whether you need technical advice, repair, orgenuine factory replacement parts, contact the Black & Decker location nearest you. To findyour local service location, refer to the yellow page directory under "Tools—Electric" or call:1-800-54-HOW TO. (544-6986)IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance andadjustment should be performed by Black & Decker Service Centers or other qualified serviceorganizations, always using identical replacement parts.FULL TWO-YEAR HOME USE WARRANTYBlack & Decker (U.S.) Inc. warrants this product for two years against any defects in materialor workmanship. The defective product will be replaced or repaired at no charge in either oftwo ways.The first, which will result in exchanges only, is to return the product to the retailer from whomit was purchased (provided that the store is a participating retailer). Returns should be madewithin the time period of the retailer’s policy for exchanges (usually 30 to 90 days after thesale). Proof of purchase may be required. Please check with the retailer for their specificreturn policy regarding returns that are beyond the time set for exchanges.The second option is to take or send the product (prepaid) to a Black & Decker owned orauthorized Service Center for repair or replacement at our option. Proof of purchase may berequired. Black & Decker owned and authorized Service Centers are listed under "Tools-Electric" in the yellow pages of the phone directory.This warranty does not apply to accessories. This warranty gives you specific legal rights andyou may have other rights which vary from state to state. Should you have any questions,contact the manager of your nearest Black & Decker Service Center. This product is notintended for commercial use.FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or aremissing, call 1-800-544-6986 for a free replacement.See ‘Tools-Electric’– Yellow Pages –for Service & SalesImported byBlack & Decker (U.S.) Inc.,701 E. Joppa Rd.Towson, MD 21286 U.S.A.Fig. 7Fig. 7aFig. 7bFig. 7cFig. 7, 7a, 7b, 7c

/ 2

Related manuals for Black & Decker Workmate 425 TYPE 5