Black & Decker Workmate 425 TYPE 5 User Manual

Also see for Workmate 425 TYPE 5: Instruction manual Manual

WARNING: Read and understand all instructions. Failure to follow all instructionslisted below may result in serious personal injury.1. Do not load with more than 550 pounds.2. Do not apply an unbalanced load which could cause the work center to tip over.3. Do not use the work center as a stepladder or standing platform. Do not use the lowerplatform as a step when the work center is in “Workbench” position. The footboard is afoot REST only.4. Do not store work center outdoors or in a damp location.5. Avoid applying excessive force when clamping with the swivel pegs.6. Be sure that the legs are fully open (for workbench height) and be sure that the tablelocks in position.7. When using a power tool with the work center, follow the safety instructions in thetool’s instruction manual.8. Always wear safety glasses when operating power tools.9. An even pressure of the vise jaws on the workpiece is essential. Tighten both crankhandles uniformly.10. When assembling your work center, use only the special plastic socket wrenchprovided. Use of other wrenches or sockets can damage your work center.SAVE THESE INSTRUCTIONS FOR FUTURE USE.ASSEMBLY1. The Workmate ®425 work center comes partially assembled. Empty the cartoncompletely onto the floor and identify all the components. (Fig. 1)2. Assemble two top blocks to the underside of the rear jaw by fitting the raised posts onthe top blocks into the smaller holes of the rear jaw. Insert bolts through the rear jawand into top blocks and tighten with supplied wrench. (Fig. 2)3. Assemble top blocks to middle jaw the same as rear jaw. (Fig. 3)4. Remove the white clip from the end of each vise screw and discard. (Clip is forprotection of part only.)5. Aligning the hole in the vise crank with the hole in the vise screw, push the vise crankonto the vise screw end (protruding from the front of the vise jaw bracket). Using ahammer, drive the supplied pin into the aligned holes. Repeat this procedure for theinstallation of the other vise crank. (Fig. 4)6. Complete the assembly by pushing the snap-in knobs into the holes in the vise cranks.(Fig. 5)7. Install the front vise jaw on top of the top blocks so that the small holes at each end ofthe vise jaw fit down over the posts on the top side of the blocks. With the jawpositioned as described above insert into the frame as shown in figure 6. Insert a boltinto the holes in the jaw and tighten them securely into the holes in the pivot nut. Usethe socket wrench provided.8. Tip the front of the Workmate® up and rest it against your knee as shown in Fig. 7. Pullupwards on both left and right release levers to unlock Workmate® (Fig. 7a). Using bothhands, push the top of the Workmate® up and away from you while holding the footrestwith your other hand until the frame locks in place. (Fig.7b) Note: New Workmate® arestiff and require more effort to raise into the locked working position. To close theWorkmate® for storage, pull upward on the two release levers to unlock theWorkmate®. While holding the levers up pull back and down to close the Workmate®.(Fig.7c)FEATURES & APPLICATIONSVERTICAL CLAMPING9. Pull vertical locking bar toward yourself and lift front vise jaw until it is in vertical, lockedposition Note: Rear jaw must be in middle “keyhole” position. (Fig. 8)CHANGING THE INDEXED POSITION OF THE REAR JAW10. Install rear jaw in one of three possible indexed “keyhole” positions by inserting theindexing lug into a keyhole in the vise jaw bracket. Secure the rear jaw by moving rearjaw to the back of the key hole. (Fig. 9)VEA EL ESPAÑOL EN LA CONTRAPORTADA.SAVE THIS MANUAL FOR FUTURE REFERENCE.INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.Cat No. WM425 Type 5 Form # 632231-00 (APR-05)Copyright © 2005 Black & Decker Printed in ChinaBEFORE RETURNING THIS PRODUCTFOR ANY REASON PLEASE CALL1-800-54-HOW-TO (544-6986)IF YOU SHOULD EXPERIENCE A PROBLEMWITH YOUR BLACK & DECKER PRODUCT,CALL 1-800-54-HOW-TO (544-6986)BEFORE YOU CALL, HAVE THE FOLLOWING INFORMATION AVAILABLE, CATALOG No., TYPE No., ANDDATE CODE. IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN RESOLVE YOURPROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOURFEEDBACK IS VITAL TO BLACK & DECKER.REAR JAWMÂCHOIRE ARRIÈREMORDAZA TRASERAMIDDLE JAWMÂCHOIRE CENTRALEMORDAZA MEDIAFOLDING LEGSPIEDS ESCAMOTABLESPATAS PLEGABLESFOOTREST (NO STEP)REPOSE-PIED (PAS UN MARCHE-PIED)DESCANSO PARA LOS PIES (NO ESCALON)CRANKMANIVELLEMANIVELAFRONT VISE JAWMÂCHOIRE AVANTMORDAZA FRONTALVERTICAL LOCKING BARBARRE DE VERROUILLAGEVERTICALEBARRA DE FIJACION VERTICALSNAP-IN KNOBSBOUTONS ÀENCLENCHEMENT RAPIDEMANGOS DE LA MANIVELARELEASE LEVERLEVIER DE DÉGAGEMENTPALANCA DE LIBERACIÓNWorkmate®425 TYPE 5

/ 2

Related manuals for Black & Decker Workmate 425 TYPE 5