Keysight Technologies E1420B manuals

E1420B

Brand: Keysight Technologies | Category: Cash Counter

Table of contents

1. declaration of conformity
2. Table Of Contents
3. Table Of Contents
4. Table Of Contents
5. Table Of Contents
6. Table Of Contents
7. Table Of Contents
8. Table Of Contents
9. Table Of Contents
10. Table Of Contents
11. Table Of Contents
12. Table Of Contents
13. Keysight 75000 SERIES C DOCUMENTATION
14. How To Use This Manual
15. Chapter Guide
16. Overall Description of the E1420B
17. Additional Measurement Capabilities
18. E1420B Quick Installation/Setup
19. Hardware Setup
20. Verifying E1420B Operation
21. Executing Self-test (*TST?)
22. Making Basic Measurements
23. Interpreting Frequency Measurement Results Display
24. Making A Time Interval Measurement
25. Interpreting Time Interval Measurement Results Display
26. E1420B Service, Support And Options
28. Connectors and Indicators
29. ARM INPUT
30. VXIbus Connectors
31. Internal Configuration
32. Bus Grant and Request Configuration Procedure
33. System Default Logical Addresses
34. Installation and Verification
36. Programming the E1420B
37. Series 200/300 HP BASIC
38. Initialization State
39. Changing Default Parameters
40. Measurement Task Tutorials
41. Example: Making A Frequency Measurement
42. Frequency Measurement Program Example
43. Period Measurement
44. Period Measurement Program Example
45. Example: Making A Time Interval Measurement
46. Time Interval Measurement Program Example
47. Comments
48. Input Signal Conditioning
50. Ratio Measurement Program Example
51. Totalize Measurement
52. Totalize Measurement Program Example
53. Rise/Fall Time Measurement
55. Example: Making A Voltage Measurement
56. Voltage Measurement Program Example
58. Counter Configuration And The Measurement Procedure
59. E1420B Measurement Procedure
60. Making Measurements with SCPI
61. The MEASure, CONFigure, and SENSe Commands
62. Using CONFigure
63. The INITiate, READ?, and FETCh? Commands
64. Using FETCh
65. Frequency/Period Measurements
66. Channel 3 Trigger Level
68. Measurement Definition and Range
69. Time Interval Measurements
70. Slope Selection
71. Totalize Measurements
72. Reading Measurement Results
73. Voltage Measurements
75. Input Range
76. Input Sensitivity
77. Input Attenuation
78. Input Coupling
79. Trigger Level
80. Trigger Slope
81. Input Impedance
82. Damage Level
83. Arming the Counter
84. Internal Arming
85. External Arming
86. TTL Trigger Lines
87. Measurement Resolution
88. Resolution And Gate Time Calculations
89. Output Formats
90. Min/Max/AC/DC
92. Command Types
93. Implied Channel
94. Optional Parameters
95. Linking Commands
96. Command Summary
97. SCPI Commands
98. IEEE 488.2 Common Commands
99. EMC (Enable Macro)
100. ESE (Standard Event Status Enable)
101. IDN? (Identification Query)
102. RST (Reset)
103. SRE? (Service Request Enable Query)
104. E1420B SCPI COMMANDS
105. Subsystem Syntax
106. LEVel
107. SLOPe
108. SOURce
109. FREQuency
110. FREQuency:RATio
111. FTIMe and :FALL:TIME
112. MAXimum
113. MINimum
114. PERiod
115. PWIDth
116. RTIMe and :RISE:TIME
117. TINTerval
118. TOTalize
119. CONFigure
120. DIAGnostics
121. CALibrate
122. READ:MRC? <EREG/TREG
123. UFAil[?]
124. INITiate
125. IMMediate]
126. CONTinuous
127. INPut
128. ATTenuation
129. IMPedance
130. ROUTe
131. MEASure
132. MEASure Command Details
133. MEMORY Subsystem (Option 040)
134. VME:ADDRess
135. VME:SIZE
136. VME:STATe
137. OUTPut
138. ROSCillstor:STATe
139. READ
140. SENSe
141. AVERage{:STATe}
142. AVERage[:STATe]
143. EVENt:LEVei[:ABSOlute]
144. EVENt:LEVel:RELative
145. EVENt:SLOPe
146. EVENt:HYSTeresis
147. FREQuency:RANGe
148. FREQuency:RANGe[:UPPer]
149. FUNCtion
150. PERiod:APERture
151. ROSCillator:SOURce
152. TINTerval:DELay:TIME
153. TOTalize:GATE:STATe
154. TOTalize:GATE:POLarity
155. STATus
156. Using the Operation Status Register
157. OPERation:CONDition
158. OPERation[:EVENt]
159. QUEStionable:CONDition
160. SYSTem
161. PIMacro
162. A Specifications
163. B Error Messages
164. Introduction
165. Equipment Required
166. Calibration Cycle
167. Software Implemented Full Performance Testing
168. Preliminary Procedure
169. Auto Frequency Measurement Test
170. Ratio Measurement Test
171. Input Signal Conditioning Test
172. Time Interval Test
173. External Arm Input Test
174. Option 010 TCXO Timebase Test
175. Option 030, Input 3 Test
176. Full Performance Tests
177. Specifications Tested
178. Uncertainties Analysis Method
179. Alternate Test Equipment
181. Input Condition B
182. Input Condition C
183. Input Condition D
184. Input Condition E
185. External Arm Range, Sensitivity, and Minimum Start-to-Stop Time Tests
187. Auto Measurement Sensitivity, Range, and Accuracy Tests
189. Option 030) Input 3: Sensitivity, Range, and Accuracy Tests
190. Functional Performance Test Records
191. Appendix Guide
192. Monitoring Program Errors
193. How the Error Queue Works
194. Running Self-Test
196. Shared Memory Programming
197. Retrieve Data
198. C" EXAMPLE PROGRAM
200. Option Identification Query Common Command
201. Phase Measurement
203. Query Response
204. Specifications
205. Performance Test
206. Acquisition Timeout
208. Acquisition Timeout Programming Example
209. Functional Limitations
210. Accuracy
211. Input Impedance Default Control
212. Input Impedance Default Control Programming Example
213. Option Identification Query

E1420B

Brand: Keysight Technologies | Category: Cash Counter