red lion PAXCK Manual

Also see for PAX: Product manual Manual Bulletin

red lion PAXCK Manual Manual pdf 1 page image

1z 6-DIGIT 0.56" RED SUNLIGHT READABLE DISPLAYz 4 SEPARATE DISPLAYS (Timer, Counter, Real-Time Clock, and Date)z CYCLE COUNTING CAPABILITYz PROGRAMMABLE FUNCTION KEYS/USER INPUTSz FOUR SETPOINT ALARM OUTPUTS (W/Plug-in card)z COMMUNICATIONS AND BUS CAPABILITIES (W/Plug-in card)z BUS CAPABILITIES: DEVICENET, MODBUS and PROFIBUS-DPz CRIMSON® PROGRAMMING SOFTWAREz NEMA 4X/IP65 SEALED FRONT BEZELGENERAL DESCRIPTIONThe PAXTM (PAX ® Timer) and PAXCK (PAX ® Clock/Timer) offer manyfeatures and performance capabilities to suit a wide range of industrialapplications. Both can function as an Elapsed Timer or Preset Timer, while thePAXCK also offers Real-Time Clock with Date capability. The Plug-in optioncards allow the opportunity to configure the meter for the present application,while providing easy upgrades for future needs.Both units can function as an Elapsed Time Indicator. By using two separatesignal inputs and 23 selectable timer ranges, the meters can be programmed tomeet most any timing application. With the addition of a Plug-in Setpoint card,they can easily become a dual or quad output preset timer.The PAXCK can also operate as a Real-Time Clock (RTC), with the Real-Time Clock Card already installed. The meter is capable of displaying time in12 or 24-hour time formats. The 12-hour format can be displayed in hours andminutes, with or without an AM/PM indication or in hours, minutes, andseconds. The 24-hour format can be displayed in hours and minutes or in hours,minutes, and seconds. The PAXCK is also capable of a calendar display inwhich the day, month and/or year can be displayed. The meter will recognizeleap years, and can automatically adjust for Daylight Savings Time. The Real-Time Clock has the ability to externally synchronize with other PAXCK metersto provide a uniform display network throughout the plant.If the application calls for both a Preset Timer and a Real-Time Clock at thesame time, the PAXCK can handle this requirement as well. The meter providesup to four different displays, accessed via front panel push buttons or externalinputs. The displays are Timer (TMR), which displays the current timer value;Count (CNT), which displays the current cycle counter value; Date (DAT),which displays the current programmed date; and Real-Time Clock, whichdisplays the current time. A battery-backed Real-Time Clock plug-in card isprovided with the PAXCK. This card, which includes a lithium coin-cell battery,will maintain the time and date when main power is removed.The meters accept inputs from a variety of sources including switch contactsand outputs from CMOS or TTL circuits. The input can be configured to triggeron the edge or level of the incoming pulse. Internal jumpers are available to allowthe selection for sinking inputs (active low) or sourcing inputs (active high).The front panel keys and three user inputs are programmable to performvarious meter functions. One of the functions includes exchanging parameterlists, allowing for two separate listings of setpoint values, timer start/stopvalues, counter start/stop values and RTC daily on and off values.The meters can have up to four setpoint outputs, determined by the optionalplug-in cards. The setpoint plug-in cards provide dual FORM-C relays (5A),quad FORM-A relays (3A) or either quad sinking or quad sourcing opencollector logic outputs. The outputs can be assigned to the timer, counter, RTCdate, and RTC time. The outputs can also be independently configured to suit avariety of control and alarm requirements.Plug-in cards can also provide serial communications. These include RS232,RS485, Modbus, DeviceNet, and Profibus-DP. Display values, setpoint alarmvalues and setpoint states can be controlled through serial communications.With the RS232 or RS485 communication card installed, it is possible toconfigure the meter using a Windows® based program. The meter configurationdata can be saved to a file for later recall.Once the meters have been initially configured, the parameter list may belocked out from further modification entirely, or the setpoint, timer start/stopvalues, counter start/stop values, RTC time SET, and Display Intensity can bemade accessible. This lockout is possible through a security code or user input.The meters have been specifically designed for harsh industrial environments.With a NEMA 4X/IP65 sealed bezel and extensive testing to meet CErequirements, the meter provides a tough yet reliable application solution.SAFETY SUMMARYAll safety related regulations, local codes and instructions that appear in thisliterature or on equipment must be observed to ensure personal safety and toprevent damage to either the instrument or equipment connected to it. Ifequipment is used in a manner not specified by the manufacturer, the protectionprovided by the equipment may be impaired.Do not use this unit to directly command motors, valves, or other actuatorsnot equipped with safeguards. To do so can be potentially harmful to persons orequipment in the event of a fault to the unit.MODEL PAX-1/8 DIN PRESET TIMER (PAXTM) &REAL-TIME CLOCK (PAXCK)CAUTION: Risk of Danger.Read complete instructions prior toinstallation and operation of the unit.CAUTION: Risk of electric shock.DIMENSIONS In inches (mm) Note: Recommended minimum clearance (behind the panel) for mountingclip installation is 2.1" (53.4) H x 5" (127) W.C US LISTEDUS LISTEDULRIND. CONT. EQ.51EBBulletin No. PAXCK-GDrawing No. LP0524Released 2/08Tel +1 (717) 767-6511Fax +1 (717) 764-0839www.redlion.net