Vanguard SBVBN(A) Owner's Operation And Installation Manual

Also see for SBVBN: OPERATING AND INSTALLATION Manual

Contents

Vanguard SBVBN(A) Owner's Operation And Installation Manual Manual pdf 19 page image

19105500OWNER’S MANUAL1. After lighting, let pilot flame burn forabout one minute. Turn control knobon the control valve to ON position.Turn flame adjustment knob any-where between HI and LO. Slide theselector switch to the REMOTE posi-tion.Note: The burners may light ifhand-held remote ON button was onwhen selector switch was last turnedoff. You can now turn the burners onand off with either optional hand-heldremote control unit.IMPORTANT: Do not leave the se-lector switch in the REMOTE posi-tion when the pilot is not lit. This willdrain the battery.IMPORTANT: Be sure to press theON/OFF buttons on the hand-heldremote control unit for up to 3 sec-onds to assure proper operation.OPTIONAL REMOTEOPERATIONNote: All remote control accessories mustbe purchased separately (See Accessorieson page 27). Follow instructions includedwith the remote control.Thermostat Control Operation(Optional GHRCT Only) The thermostatcontrol setting on the remote control unitcan be set to any comfort level between HIand LO. The burners will turn on and offautomatically to maintain the comfort levelyou select. The ideal comfort setting willvary by household depending upon theamount of space to be heated, the output ofthe central heating system, etc.NOTICE: You must light the pilotbefore using the hand-held re-mote control unit. SeeLightingInstructions, page 18 .OPERATINGFIREPLACEContinuedFigure 46 - Setting the (GHRC) RemoteControl Selector Switch, Valve ControlKnob, and Flame Adjustment Knob forRemote OperationContinuedGHRC Series Operation:2a. Press the ON/OFF button to turn theburners on and off. When turningburners off, the pilot will remain lit.GHRCT Series Operation:2b. Select the MAN (manual) or AUTObutton on the hand-held remote con-trol unit (see Figure 48).• In manual mode, turn burners onor off by pressing the ON or OFFbuttons on the hand-held remotecontrol unit.Figure 47 - Setting the (GHRCT) SelectorSwitch, control Knob, and FlameAdjustment Knob for Remote OperationTEMPSTATUSHILOMAN ONAUTO OFFFigure 48 - Hand-Held Thermostat Remote Control Unit Selections(GHRCT Only)Shows TemperatureSettingAllows Burners to beTurned On and Offwith the Hand-HeldRemote UnitThe Heater willAutomatically CycleBetween Pilot andthe Heat Setting thathas been SelectedIncreases RoomTemperatureDecreases RoomTemperatureTurns Burners Onand OffShows CurrentOperation Mode• In auto mode, the room tempera-ture is controlled by the thermo-stat in the hand-held remote con-trol unit. To increase the room tem-perature, press the top arrow of theTEMP button. To lower the roomtemperature, press the bottom ar-row of the TEMP button. At highersettings the heater will run more.IMPORTANT: This remote controlhas been specially engineered to takean air temperature sample every 5.5minutes in auto mode. It will not re-spond immediately to the tempera-ture setting being turned up or down.IMPORTANT: The hand-held remotecontrol unit must be near the heaterbut not extremely close to it. Thethermostat on the hand-held remotecontrol unit will heat up too quicklyand turn the heater off.3. Use the STATUS button on the hand-held remote control unit to see theoperation mode being used and thetemperature setting selected. A redlight will come on beside the opera-tion mode being used.4. To turn the burners off when operat-ing in the manual mode, press the OFFbutton. If operating in the auto mode,press the MAN button, then press theOFF button. The pilot will remain lit.IMPORTANT: To turn the pilot off,manually turn the control knob on theheater to the OFF position.REMOTE OFF ONLOHIOFF ONPILOTSelector Switch in RemotePosition (GHRC OptionalRemote Control) Control Knob inOn PositionFlame Adjustment KnobONOFFREMOTELOHIOFF ONPILOTSelector Switch inRemote Position(GHRCT OptionalRemote Control)Flame Adjustment KnobControl Knobin On Position