Vanguard SBVBN(A) Owner's Operation And Installation Manual

Also see for SBVBN: OPERATING AND INSTALLATION Manual

Contents

Vanguard SBVBN(A) Owner's Operation And Installation Manual Manual pdf 18 page image

18®B-VENT FREESTANDING FIREPLACE105500TO TURN OFF GASTO APPLIANCE1. Open lower louver panel.2a. Set selector switch in the “OFF”position.2b. If Using Optional Hand-Held Re-mote: Set selector switch in the OFFposition to prevent draining battery.3. Turn off all electrical power to theappliance if service is to be performed.4. Push in gas control knob slightly andturn clockwise to “OFF”.5. Close lower panel.Shutting Off Burners Only (pilotstays lit)You may shut off the burners and keepthe pilot lit by doing one of the following:1. Turn control knob clockwiseto the PILOT position.2. Set selector switch in the OFF position.MANUAL LIGHTINGPROCEDURE1. Remove glass door (see Removing/Replacing Glass Door, page 16).2. Follow steps 1 through 8 under Light-ing Instructions.3. Depress control knob and light pilotwith match.4. Keep control knob pressed in for 30seconds after lighting pilot. After 30seconds, release control knob. Nowfollow steps 10 through 14, column 2.5. Replace glass door (see Removing/Replacing Glass Door, page 16).OPERATINGFIREPLACEWARNING: If you do not fol-low these instructions exactly, afire or explosion may result caus-ing property damage, personalinjury or loss of life.A. This appliance has a pilot which mustbe lighted by hand. When lighting thepilot, follow these instructions exactly.B. BEFORE LIGHTING smell allaround the appliance area for gas. Besure to smell next to the floor becausesome gas is heavier than air and willsettle on the floor.WHAT TO DO IF YOU SMELL GAS• Do not try to light any appliance.• Do not touch any electric switch; donot use any phone in your building.• Immediately call your gas supplierfrom a neighbor's phone. Followthe gas supplier's instructions.C. Use only your hand to push in or turnthe gas control knob. Never use tools.If the knob will not push in or turnby hand, don't try to repair it, call aqualified service technician. Force orattempted repair may result in a fireor explosion.D. Do not use this appliance if any parthas been under water. Immediatelycall a qualified service technician toinspect the appliance and to replaceany part of the control system andany gas control which has been un-der water.FOR YOUR SAFETYREAD BEFORELIGHTINGLIGHTINGINSTRUCTIONS1. STOP! Read the safety informationin column one.2. Open lower panel.3. Turn ON/OFF switch to “OFF”.4. Turn off all electric power to thefireplace.5. Push in gas control knob slightly andturn clockwise to “OFF”.6. Wait five (5) minutes to clear out anygas. Then smell for gas, includingnear the floor. If you smell gas,STOP! Follow “B” in the safety in-formation in column one. If you don'tsmell gas, go to the next step.7. The pilot is located by the mainburner and should not require ac-cessing for lighting.8. Turn knob on gas control counter-clockwise to “PILOT”.9. Push in control knob all the way andhold. Immediately light the pilot byrepeatedly depressing the piezospark ignitor until a flame appears.Continue to hold for about one (1)minute after the pilot is lit. Releaseknob and it will pop back. Pilotshould remain lit. If it goes out, re-peat steps 5 through 8.• If knob does not pop up when re-leased, stop and immediately call yourservice technician or gas supplier.• If the pilot will not stay lit after sev-eral tries, turn the gas control knobto “OFF” and call your servicetechnician or gas supplier.10. Turn gas control counterclockwiseto “ON”.11. Turn on all electric power to thefireplace.12. Turn the ON/OFF switch to ONposition.13. This valve is equipped with a HI/LOfeature. Set fireplace input as desired.14. Close lower panel.Figure 45 - Control ValveLOHIOFF ONPI LOTGas ControlKnobVariableControl KnobPiezo Ignitor