OneStart

Menu
Toshiba XLTR-200 Instruction Manual Manual pdf 74 page image

Toshiba XLTR-200 Instruction Manual

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 previewPage 31 previewPage 32 previewPage 33 previewPage 34 previewPage 35 previewPage 36 previewPage 37 previewPage 38 previewPage 39 previewPage 40 previewPage 41 previewPage 42 previewPage 43 previewPage 44 previewPage 45 previewPage 46 previewPage 47 previewPage 48 previewPage 49 previewPage 50 previewPage 51 previewPage 52 previewPage 53 previewPage 54 previewPage 55 previewPage 56 previewPage 57 previewPage 58 previewPage 59 previewPage 60 previewPage 61 previewPage 62 previewPage 63 previewPage 64 previewPage 65 previewPage 66 previewPage 67 previewPage 68 previewPage 69 previewPage 70 previewPage 71 previewPage 72 previewPage 73 previewPage 74 previewPage 75 previewPage 76 previewPage 77 previewPage 78 previewPage 79 previewPage 80 previewPage 81 previewPage 82 previewPage 83 previewPage 84 previewPage 85 previewPage 86 previewPage 87 previewPage 88 previewPage 89 previewPage 90 previewPage 91 previewPage 92 previewPage 93 previewPage 94 previewPage 95 previewPage 96 previewPage 97 previewPage 98 previewPage 99 preview
Contents
  1. usage precautions
  2. Table Of Contents
  3. Table Of Contents
  4. Table Of Contents
  5. The Network Gateway Series Concept
  6. Feature Summary
  7. Installing the Gateway
  8. DIN Rail Mounting
  9. Installation for Non-Toshiba ASD Networks
  10. Installation for G7 ASDs
  11. Installation for S7, S9, S11, A7 and VF-nC1 ASDs
  12. RS485 Port Electrical Interfaces
  13. Environmental Specifications
  14. Maintenance and Inspection
  15. Storage and Warranty
  16. LED Indicators
  17. Auxiliary Power Supply
  18. Unit Configuration Concepts
  19. Point Configuration
  20. General Configuration Procedure
  21. Console Access
  22. Application Configuration
  23. Invocation
  24. Main Menu
  25. View/Edit Points
  26. View/Edit Ports
  27. Load Points
  28. XLTR-200 Information
  29. Protocol-Specific Information
  30. Coil Mappings
  31. Modbus RTU Slave
  32. Metasys N2
  33. Toshiba Common Serial ASD Protocol
  34. Mitsubishi ASD Protocol
  35. Siemens FLN
  36. Supported Subpoints
  37. Subpoint Details
  38. Toshiba 3-Series ASD Protocol
  39. Command Parameters
  40. Monitor Parameters
  41. Fundamental Parameters #1
  42. Fundamental Parameters #2
  43. Terminal Selection Parameters
  44. Special Control Parameters
  45. Frequency Setting Parameters
  46. Protection Function Parameters
  47. Pattern Run Control Parameters
  48. Feedback Control Parameters
  49. Communication Setting Parameters
  50. AM/FM Terminal Adjustment Parameters
  51. Utility Parameters
  52. Motor Rating Parameters
  53. Inverter Fault Codes
  54. Firmware Updates
  55. Using the RFU Utility
  56. Transmitting Firmware Files
  57. Wrap-Up
  58. Notes
Toshiba XLTR-200 Instruction Manual Manual pdf 74 page image
73Table 9: Input Terminal SelectionsSettingValueData(Hex) Function SettingValueData(Hex) Function0 10C8 R (reverse run) 28 04AF Binary bit #61 011C SS1 (preset speed selection) 29 08AF Binary bit #72 021C SS2 (preset speed selection) 30 10AF Binary bit #83 041C SS3 (preset speed selection) 31 20AF Binary bit #94 081C SS4 (preset speed selection) 32 40AF Binary bit #105 20C8 F (forward run) 33 04CE No effect6 201B RES (fault reset) 34 01C7 UP/DOWN frequency setting (UP)7 C0C9 ST (gate ON/OFF) 35 02C7 UP/DOWN frequency setting(DOWN)8 0CC8 JOG selection 36 04C7 UP/DOWN frequency clear9 081A Accel / decel #1/#2 selection 37 08C7 PUSH-type RUN key10 101B Emergency off 38 10C7 PUSH-type STOP key11 021B DC injection braking ON/OFF 39 02B9 No effect12 041B Fundamental parameterswitching (V/F #2)40 C0C8 Forward/reverse run selection13 011B Feedback control ON/OFF 41 20C7 RUN14 10CE Pattern run selection #1 42 30C9 Binary data write15 20CE Pattern run selection #2 43 0198 [LOCAL/REMOTE] key16 40CE Pattern run selection #3 44 0298 [MON] key17 80CE Pattern run selection #4 45 0498 [PRG] key18 02CE Pattern run continue signal 46 0898 [UP] key19 01CE Pattern run step trigger signal 47 1098 [DOWN] key20 0AC9 JOG forward run 48 2098 [READ/WRITE] key21 06C9 JOG reverse run 49 4098 [RUN] key22 10AE Binary bit #0 50 8098 [STOP/CLEAR] key23 20AE Binary bit #1 51 08CE Commercial power / inverterswitching signal24 40AE Binary bit #2 52 40C7 Reserved for option use25 80AE Binary bit #3 53 10CB RR frequency switching input26 01AF Binary bit #4 54 20CB IV frequency switching input27 02AF Binary bit #5Note: In order for binary bit #0 ∼ #10 (setting values 22 ∼ 32) and UP/DOWN frequency setting (setting values 34 &35) inputs to be valid, parameter FREQUENCY PRIORITY SELECTION #1 or FREQUENCY PRIORITYSELECTION #2 in GROUP:FREQUENCY SETTING PARAMETERS must be set to 5 (BIN (binary setting orUP/DOWN setting)).
/ 99
Related manuals for Toshiba XLTR-200
Toshiba ProtoNode Quick Install Manual first page preview
Toshiba ProtoNode Quick Install Manual
Toshiba T1-40 PLC Specification first page preview
Toshiba T1-40 PLC Specification
This manual is suitable for:
XLTR-200
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved