Sony MDX-F5800 Installation/connections Manual

Also see for MDX-F5800: Limited warranty Operating & installation instructions Installation/connections Operating instructions Operating instructions

© 2004 Sony Corporation Printed in Thailand3-262-943-11 (1)Caut ions• This unit is designed for negative ground 12 V DCoperation only.• Do not get the leads under a screw, or caught inmoving parts (e.g. seat railing).• Before making connections, turn the car ignitionoff to avoid short circuits.• Connect the yellow and red power input leadsonly after all other leads have been connected.• Run all ground leads to a common groundpoint.• Be sure to insulate any loose unconnected leadswith electrical tape for safety.• The use of optical instruments with this productwill increase eye hazard.Notes on the power supply lead (yellow)• When connecting this unit in combination withother stereo components, the connected carcircuit’s rating must be higher than the sum ofeach component’s fuse.• When no car circuits are rated high enough,connect the unit directly to the battery.Part s Iist (1)• The numbers in the list are keyed to those in theinstructions.• The bracket 1 and the protection collar 3 areattached to the unit before shipping. Beforemounting the unit, use the release keys 5 toremove the bracket 1 and the protection collar 3from the unit. For details, see “Removing theprotection collar and the bracket (4)” on thereverse side of the sheet.• Keep the release keys 5 for future use as theyare also necessary if you remove the unit fromyour car.Caut ionHandle the bracket 1 carefully to avoid injuringyour fingers.NoteBef ore inst alling, make sure t hat t he cat ches on bot hsides of t he bracket 1 are bent inw ards 2 mm (3/32 in). Ift he cat ches are st raight or bent out w ards, t he unit w illnot be inst alled securely and may spring out .Connect ion exam ple (2)Notes (2-A)• Be sure t o connect t he ground lead bef ore connect ingt he amplif ier.• If you connect an opt ional pow er amplif ier and do notuse t he built -in amplif ier, t he beep sound w ill bedeact ivat ed.Tip (2-B- )For connect ing t w o or more M D/CD changers, t he sourceselect or XA-C30 (opt ional) is necessary.Inst allat ion/Connect ionsInst allat ion/ConnexionsInst alación/ConexionesFM /AMM iniDisc PlayerConnect ion diagram (3)1 To a metal surface of the carFirst connect t he black ground lead, t hen connectt he yellow and red pow er input leads.2 To the power antenna control lead or powersupply lead of antenna booster amplifierNotes• It is not necessary t o connect t his lead if t here is nopow er ant enna or ant enna boost er, or w it h amanually-operat ed t elescopic ant enna.• When your car has a built -in FM /AM ant enna int he rear/side glass, see “ Not es on t he cont rol andpow er supply leads.”3 To AMP REMOTE IN of an optional poweramplifierThis connect ion is only f or amplif iers. Connect ingany ot her syst em may damage t he unit .4 To the interface cable of a car telephone5 To the +12 V power terminal which is energizedin the accessory position of the ignition keyswitchNotes• If t here is no accessory posit ion, connect t o t he +12V pow er (bat t ery) t erminal w hich is energized atall t imes.Be sure t o connect t he black ground lead t o amet al surf ace of t he car f irst .• When your car has a built -in FM /AM ant enna int he rear/side glass, see “ Not es on t he cont rol andpow er supply leads.”6 To the +12 V power terminal which is energizedat all timesBe sure t o connect t he black ground lead t o a met alsurf ace of t he car f irst .Notes on the control and pow er supply leads• The pow er ant enna cont rol lead (blue) supplies +12 VDC w hen you t urn on t he t uner.• When your car has built -in FM /AM ant enna in t he rear/side glass, connect t he pow er ant enna cont rol lead(blue) or t he accessory pow er input lead (red) t o t hepow er t erminal of t he exist ing ant enna boost er. Fordet ails, consult your dealer.• A pow er ant enna w it hout a relay box cannot be usedw it h t his unit .M emory hold connectionWhen t he yellow pow er input lead is connect ed, pow erw ill alw ays be supplied t o t he memory circuit even w hent he ignit ion sw it ch is t urned of f .Notes on speaker connection• Bef ore connect ing t he speakers, t urn t he unit of f .• Use speakers w it h an impedance of 4 t o 8 ohms, andw it h adequat e pow er handling capacit ies t o avoid it sdamage.• Do not connect t he speaker t erminals t o t he carchassis, or connect t he t erminals of t he right speakersw it h t hose of t he lef t speaker.• Do not connect t he ground lead of t his unit t o t henegat ive (–) t erminal of t he speaker.• Do not at t empt t o connect t he speakers in parallel.• Connect only passive speakers. Connect ing act ivespeakers (w it h built -in amplif iers) t o t he speakert erminals may damage t he unit .• To avoid a malf unct ion, do not use t he built -in speakerleads inst alled in your car if t he unit shares a commonnegat ive (–) lead f or t he right and lef t speakers.• Do not connect t he unit ’s speaker leads t o each ot her.Note on connectionIf speaker and amplif ier are not connect ed correct ly,“ FAILURE” appears in t he display. In t his case, make suret he speaker and amplif ier are connect ed correct ly.1 3215× 24M DX-F5800Catch1× 4AUDIO OUT REARAUDIO OUT FRONTBUS AUDIO INBUS CONTROL INBUS CONTROL INBUS AUDIO IN2ABSource selector*Sélecteur de source*Selector de fuente*XA-C30* not suppliednon f ournino suminist radoEquipm ent used in illust rat ions (not supplied)Appareils ut ilisés dans les illust rat ions (non fournis)Equipo ut ilizado en las ilust raciones (no sum inist rado)Rear speakerHaut-parleur arrièreAltavoz posteriorFront speakerHaut-parleur avantAltavoz frontalMD/CD changerChangeur de MD/CDCambiador de MD/CDActive subwooferCaisson de graves actifAltavoz potenciador degraves activoRotary commander RM-X4SSatellite de commande RM-X4SMando rotatorio RM-X4SPower amplifierAmplificateur de puissanceAmplificador de potenciaDownloaded from: https://www.usersmanualguide.com/

/ 5

Related manuals for Sony MDX-F5800