Sharp SPC276 Manual

FeaturesSPC276 Digital Alarm Clock withBluetooth & Sleep Sounds1. PM indicator2. Alarm indicator3. TIME button4. SOUND button for sleep5. BLUETOOTH button6. ALARM button.7. SNOOZE / DIMMER / SLEEP TIME / VOLUME (Rotary Dial)8. SLEEP mode LED9. BLUETOOTH LED10. DC 5V jack11. Battery compartmentCare of Your Clock• Replace the back up battery annually, or store the clock without a battery.When not in use. A soft cloth or a paper towel may be used to clean your clock.Do not use any corrosive cleanser or chemical solutions on the clock. Keep the clockclean and dry to avoid any problems.Power Supply• Insert the AC adapter into a 120V AC ~ 60Hz mains outlet and the other end of thecord into the DC 5V jack on the back of the unit.Setting the Time• Press and hold the TIME button for 2 seconds to activate time setting,the hour digit will flash. Use the DIAL to rotate to the correct hour.The PM indicator will appear when the hour is advanced into the PM time.• After the hour is set, press the TIME button again, the minute digits will flash.Use the DIAL to rotate to the correct minute.• Press the TIME button to save and exit the time setting or automatically save andexit after 20 seconds without any action.Setting the Alarm• Press and hold the ALARM button for 2 seconds to activate alarm setting,the hour digit will flash. Use the DIAL to rotate to the correct hour.The PM indicator will appear when the hour is advanced into the PM time.• After the hour is set, press the ALARM button again, the minute digits will flash.Use the DIAL to rotate to the correct minute.• After the minute is set, press the ALARM button again, the display will show 10(default alarm volume is 10, max 16) use the DIAL to adjust the volume. As yourotate the DIAL the volume of the beep will correspond to the number on the display.• Press the ALARM button to save and exit the alarm setting.Using the Alarm• Press the ALARM button, the ALARM indicator will light on the display and willsound at the preset time.• Press the ALARM button again, the ALARM indicator will no longer be visible andthe alarm will remain OFF.Snooze Function (rotary dial button)• When the wake-up alarm is sounding press SNOOZE/DIMMER dial to activate theSNOOZE, this will cause the alarm to pause and the alarm will sound again in 9minutes. This will happen each time when the SNOOZE/DIMMER dial is pressed.Dimmer Function (rotary dial button)• Press the SNOOZE/DIMMER DIAL to use the display DIMMER. There are FIVElevels of display brightness: 100% / 50% / 25% / 10% / 5%(100% brightness is the default setting)Battery Backup• Remove the BATTERY DOOR and insert 2 new “AAA” batteries (not included) in thedirection of the polarity symbols.• Please make sure the batteries are new and inserted correctly.• The battery will hold the ALARM and TIME settings if the power is interrupted.There will be no display under battery power and the ALARM will sound at thecorrect time. If there is no battery and the power is interrupted, the display willflash 12:00 and the ALARM / TIME will need to be reset.Volume Control (rotary dial button)• When playing a SLEEP SOUND or using BLUETOOTH, rotate the DIAL to increase ordecrease the volume. The display will show the current volume level(volume level 0-16).Sleep Timer Function (rotary dial button)• When playing a SLEEP SOUND or using BLUETOOTH, press and hold the DIAL androtate to set the SLEEP timer for 90 / 60 / 30 minutes. Release the dial when yourdesired SLEEP time is shown and press the dial again to confirm.The SLEEP SOUND or BLUETOOTH will automatically turn OFF to the set time.• To view the remaining SLEEP time press the DIAL and the display will show theremaining sleep time.NOTE: The dimmer function will not operate when the sleep timer is active.Bluetooth Function• Press the BLUETOOTH button to enter BLUETOOTH mode. The PAIRING indicatorwill flash blue quickly. Using the native controls on your Bluetooth device(e.g. smartphone), select “SHARP” in your Bluetooth settings to pair.• When successfully paired and connected, the PAIRING Indicator will display a solidblue light and a chime will sound from the unit.• After initial pairing, the unit will stay paired unless unpaired manually by the useror canceled due to a reset of the Bluetooth device.• Use the native controls on the connected Bluetooth device to select a track.• To play or skip the selected track, use the native controls on the connectedBluetooth device.• Audio played through the connected Bluetooth device will now be heard throughthe speakers.• To adjust the volume, rotate the DIAL on the top of the unit.• To turn off BLUETOOTH mode, press and hold the BLUETOOTH button for 2 seconds.Playing Sleep Sounds• To play soothing SLEEP SOUNDS press the SOUND button.• Press the SOUND button again to cycle through the other sounds.(White Noise / Pink Noise / Brown Noise / Rain / Thunder / Ocean)• To adjust the volume, rotate the DIAL on the top of the unit.• To turn off SLEEP SOUNDS, press and hold the SOUND button for 2 seconds.123 4 5 69871110

/ 2

Related manuals for Sharp SPC276