Sharp SPC237A Instruction Manual & Warranty

SPC237A Qi Wireless Charging Alarm ClockInstruction Manual & WarrantyThank you for your purchase of this quality clock. The utmost care has gone into the design andmanufacture of your clock. Please read these instructions and store them in a safe place for futurereference.CONTROLS1P M indicator2. Qi indicator3. AL. VOL HI/LO switch4. ALARM 1 button5. ALARM 2 button6. SNOOZE/DIMMER button7. HOUR button8. MIN button9. TIME button10. Alarm 1 indicator11. Alarm 2 indicator12. USB charging ports13. Qi wireless charging areaCONNECTING TO THE POWER SUPPLYBegin by plugging in the power cord into a standard household outlet. The display will flash indicatingthe time is ready to be set.INSTALLING THE TIME & ALARM BACK UP BATTERYThe clock time and alarm (if set) can be maintained during a power failure by 2 x AAA batteries (notsupplied). Once the power is restored, check the time to make sure it is accurate and re-set if necessary.INSERTING THE BATTERY1. Open the battery compartment at the back of the unit by pressing on the catch and removing the cover.2. Insert 2 x AAA battery (preferably alkaline batteries) into the battery compartment, following thepolarity as shown on the diagram inside the compartment.3. Replace the battery compartment cover.Qi WIRELESS CHARGING- Place your wireless device on top of the clock, charging will begin on contact.- When wireless charging, the Qi indicator is continuously solid.Note:- When the phone is being charged your phone charging indicator will show as normal.- For maximum charging efficiency, the phone must be aligned with the center of the charging area.USB CHARGINGTo charge, connect your USB device to the USB port of this clock.Note:- Use only with devices that require 5V USB power.- Each USB port provides 2,000mA recharging current. Devices requiring more than 2,000mA should notbe used.- Charging time may vary for different devices.- This device is to be used ONLY for SMARTPHONES. Charging TABLETS & LAPTOPS will void the warranty.SETTING THE CLOCK- Press and hold the TIME button down to activate time setting.- While holding down the TIME button, press the HOUR button to advance to the correct hour. The PMindicator will light when the hour is advanced into the PM time.- While holding down the TIME button, press the MIN button to advance to the correct minute.- Release the TIME button when the correct time is shown on the display.SETTING THE ALARM- Press and hold the ALARM 1/2 button down to activate alarm setting.- While holding down the ALARM 1/2 button, press the HOUR button to advance to the correct hour.The PM indicator will light when the hour is advanced into the PM time.- While holding down the ALARM 1/2 button, press the MIN button to advance to the correct minute.- Release the ALARM 1/2 button when the correct alarm time is shown on the display.USING THE ALARM FUNCTION- Press the ALARM 1/2 button to activate the alarm and the alarm indicator will light up the display.- Slide the AL. VOL HI/LO switch to adjust the alarm volume from high to low.- Press the ALARM 1/2 button again to deactivate the alarm and the alarm indicator will no longer be visible.CARE OF YOUR CLOCK- Replace the back up battery annually, or store the clock without a battery when not in use.- A soft cloth or a paper towel may be used to clean your clock.- Do not use any corrosive cleanser or chemical solutions on the clock.- Keep your clock dry; if it gets wet, wipe it dry immediately. Keep your clock away from dust and dirt.Handle your clock carefully; do not drop it.- Do not subject the clock to excessive force, shock, dust, temperature, or humidity. Any of theseconditions may shorten the life of the clock.- Do not tamper with any of the internal components of this clock. This will invalidate the warranty andmay cause damage.Qi COMPATIBLE WITH:- Samsung Galaxy: S20 Ultra, S20 Plus, S20, Note 10 Plus 5G, Note 10 Plus, Note 10, S10 5G,S10 Plus, S10, S10e, Note 9, S9, S9+, Note 8, S8, S8+, S7, S7 Edge- Apple iPhone: SE 2020, 11 Pro Max, 11 Pro, 11, XS Max XS, XR, 8, 8 Plus and all Qi-enabledsmartphones!SNOOZE FUNCTION- Pressing the SNOOZE button after the alarm sounds will cause the alarm to pause and the alarm willsound again in 9 minutes. This will happen each time the SNOOZE button is pressed.DIMMER FUNCTION- Press the DIMMER button to adjust the brightness of the LED display.The dimmer has three levels of brightness; High, Medium & LowSAFETY WARNING:Only place Qi approved charging devices onto the charging pad. Pleasedo not place keys, coins or other metal objects onto the charging pad.The “Qi” symbol is a trademark of the Wireless Power Consortium.The product is designed for Qi Certificate.11223 4 5 6 7 8 9101113

/ 2

Related manuals for Sharp SPC237A